HP Vectra VE C/xxx 7 HP Vectra VE C/xxx Series 7 PC - Network Administration G - Page 62

NDIS 2.01 Driver for Banyan VINES Client, Installation Procedure, Create PROTOCOL.INI, CONFIG.SYS

Get HP Vectra VE C/xxx 7 PDF manuals and user guides View all HP Vectra VE C/xxx 7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 62 highlights

4 Installing Other Network Drivers NDIS 2.01 Driver for Banyan VINES Client NDIS 2.01 Driver for Banyan VINES Client The PCnet driver may be configured to run in the Banyan VINES environment for client-based systems only. Installation Procedure The steps to load the driver are as follows: 1 Compile all the files necessary for VINES. For ease of use, all of these files were placed in the C:\NDIS subdirectory. 2 Create PROTOCOL.INI, CONFIG.SYS, and AUTOEXEC.BAT (refer to the example below). a Modify the PROTOCOL.INI to reflect the changes necessary for the appropriate LAN card section. b Modify the AUTOEXEC.BAT and CONFIG.SYS to reflect changes in the DIRECTORY of where the files are to be placed. 3 Run the VINES PCCONFIG to configure the NDIS Ethernet Driver: a Select Network Card Settings. Then in the list provided, select NDIS Ethernet. b Verify that the interrupt level matches the one used by the driver (check that the "bindings" parameter is PCNTND: bindings = PCNTND). c Save and exit from PCCONFIG. 4 Restart the PC. 5 At the DOS prompt type BAN The installation is now complete. 62 English

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
4
Installing Other Network Drivers
NDIS 2.01 Driver for Banyan VINES Client
62
English
NDIS 2.01 Driver for Banyan VINES Client
The PCnet driver may be configured to run in the Banyan VINES environment for
client-based systems only.
Installation Procedure
The steps to load the driver are as follows:
1
Compile all the files necessary for VINES. For ease of use, all of these files were
placed in the
C:\NDIS
subdirectory.
2
Create PROTOCOL.INI, CONFIG.SYS, and AUTOEXEC.BAT (refer to the
example below).
a
Modify the PROTOCOL.INI to reflect the changes necessary for the
appropriate LAN card section.
b
Modify the AUTOEXEC.BAT and CONFIG.SYS to reflect changes in the
DIRECTORY of where the files are to be placed.
3
Run the VINES PCCONFIG to configure the NDIS Ethernet Driver:
a
Select
Network Card Settings
. Then in the list provided, select
NDIS
Ethernet
.
b
Verify that the interrupt level matches the one used by the driver (check that
the “bindings” parameter is PCNTND:
bindings = PCNTND
).
c
Save and exit from PCCONFIG.
4
Restart the PC.
5
At the DOS prompt type BAN
The installation is now complete.