HP Vectra VE C/xxx 7 HP Vectra VE C/xxx Series 7 PC - Network Administration G - Page 87

Loading the Remote Program Load Services, TOKEN_RING

Get HP Vectra VE C/xxx 7 PDF manuals and user guides View all HP Vectra VE C/xxx 7 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 87 highlights

5 Configuring for Remote Boot Setting Up a Novell NetWare 3.x and 4.x Server for Remote Start Loading the Remote Program Load Services Before loading RPL.NLM, create the BOOTCONF.SYS file as described above and install the Novell server with an 802.2 frame type and then load RPL.NLN. Load RPL.NLM in the same manner as any other NetWare NLM. At the server command line prompt, type: LOAD RPL (there are no parameters associated with loading RPL.NLM) Then bind RPL.NLM with your driver. For example: BIND RPL to board [ACK],[FRAME=xx],[GNS],[NODEFAULT], [PROTECT],[PS=SERVER] where: BIND This is the command used to link the LAN drivers to the communications protocol. (Refer to the Novell NetWare manual for details) RPL The name of a NetWare loadable module protocol used for remote boot. board The name of any NetWare LAN server driver that is configured for the IEEE 802.2 frame type. The IEEE 802.2 frame types are as follows: ETHERNET_802.2 Ethernet (802.3) using an 802.2 envelope. TOKEN_RING Token-Ring (802.5) using an 802.2 envelope. FDDI_802.2 FDDI using an 802.2 envelope. BIND Parameters. The parameters specified between square brackets [ ] are optional, not case sensitive, can be separated by blanks or commas, and may be entered in any order. NOTE GNS is required if you have an SFT III installation. English 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
English
87
5
Configuring for Remote Boot
Setting Up a Novell NetWare 3.x and 4.x Server for Remote Start
Loading the Remote
Program Load
Services
Before loading RPL.NLM, create the BOOTCONF.SYS file as described above and
install the Novell server with an 802.2 frame type and then load RPL.NLN.
Load RPL.NLM in the same manner as any other NetWare NLM. At the server
command line prompt, type:
LOAD RPL
(there are no parameters associated with loading RPL.NLM)
Then bind RPL.NLM with your driver. For example:
BIND RPL to board [ACK],[FRAME=xx],[GNS],[NODEFAULT],
[PROTECT],[PS=SERVER]
where:
BIND
This is the command used to link the LAN
drivers to the communications protocol. (Refer
to the
Novell NetWare
manual for details)
RPL
The name of a NetWare loadable module
protocol used for remote boot.
board
The name of any NetWare LAN server driver that
is configured for the IEEE 802.2 frame type.
The IEEE 802.2 frame types are as follows:
ETHERNET_802.2
Ethernet (802.3) using an 802.2 envelope.
TOKEN_RING
Token-Ring (802.5) using an 802.2 envelope.
FDDI_802.2
FDDI using an 802.2 envelope.
BIND Parameters
. The parameters specified between square brackets [ ] are
optional, not case sensitive, can be separated by blanks or commas, and may be
entered in any order.
NOTE
GNS is required if you have an SFT III installation.