HP Xw4600 HP xw4600 Workstation - Service and Technical Reference Guide - Page 110

Installing SATA hard drives in the optical drive bays (optional),

Get HP Xw4600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585516483
View all HP Xw4600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 110 highlights

Installing SATA hard drives in the optical drive bays (optional) 1. If necessary, remove the EMI shield. 2. Disconnect power from the system (Predisassembly procedures on page 57), remove the side access panel (Removing the side access panel on page 61), and then remove the front bezel (Removing the front bezel on page 65). 3. Place the SATA hard drive in the drive bracket (1), and then install four silver, ANSI 6-32 screws through the bracket and into the hard drive as shown in the following figure (2). Figure 5-56 Installing the hard drive in bracket 4. Install additional black, metric M3 screws into the bracket (1). Align the screws with the grooves in the optical drive bay, and then slide the drive into the workstation chassis (2). Figure 5-57 Installing the hard drive in the optical drive bay 100 Chapter 5 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
Installing SATA hard drives in the optical drive bays (optional)
1.
If necessary, remove the EMI shield.
2.
Disconnect power from the system (
Predisassembly procedures
on page
57
), remove the side
access panel (
Removing the side access panel
on page
61
), and then remove the front bezel
(
Removing the front bezel
on page
65
).
3.
Place the SATA hard drive in the drive bracket (1), and then install four silver, ANSI 6–32 screws
through the bracket and into the hard drive as shown in the following figure (2).
Figure 5-56
Installing the hard drive in bracket
4.
Install additional black, metric M3 screws into the bracket (1). Align the screws with the grooves in
the optical drive bay, and then slide the drive into the workstation chassis (2).
Figure 5-57
Installing the hard drive in the optical drive bay
100
Chapter 5
Removal and replacement procedures
ENWW