HP Xw4600 HP xw4600 Workstation - Service and Technical Reference Guide - Page 72

Replacing the side access panel, WARNING,

Get HP Xw4600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585516483
View all HP Xw4600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

WARNING! Before removing the workstation side access panel, be sure that the workstation is powered off and that the power cord is disconnected from the electrical outlet. 1. Disconnect power from the system (Predisassembly procedures on page 57). 2. Unlock any locks that may be present (cable lock or padlock). 3. Pull open the access panel handle (1). Figure 5-7 Removing the access panel 4. Slide the access panel toward the rear of the workstation and lift off the cover (2). Replacing the side access panel To replace the side access panel: 1. Place the access panel over the chassis and align the tabs along the edges of the access panel with the slots in the chassis. 2. Press the access panel down, fitting the tabs into the slots. 3. Slide the access panel toward the front of the chassis until it locks into place. Figure 5-8 Installing the access panel 62 Chapter 5 Removal and replacement procedures ENWW

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
WARNING!
Before removing the workstation side access panel, be sure that the workstation is
powered off and that the power cord is disconnected from the electrical outlet.
1.
Disconnect power from the system (
Predisassembly procedures
on page
57
).
2.
Unlock any locks that may be present (cable lock or padlock).
3.
Pull open the access panel handle (1).
Figure 5-7
Removing the access panel
4.
Slide the access panel toward the rear of the workstation and lift off the cover (2).
Replacing the side access panel
To replace the side access panel:
1.
Place the access panel over the chassis and align the tabs along the edges of the access panel
with the slots in the chassis.
2.
Press the access panel down, fitting the tabs into the slots.
3.
Slide the access panel toward the front of the chassis until it locks into place.
Figure 5-8
Installing the access panel
62
Chapter 5
Removal and replacement procedures
ENWW