HP Xw4600 HP xw4600 Workstation - Service and Technical Reference Guide - Page 41

Heading, Option, Description, F9=Boot Menu, F10=Setup, F12=Network Service Boot - raid

Get HP Xw4600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585516483
View all HP Xw4600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Table 4-1 Computer Setup (F10) Utility menu descriptions (continued) Heading Option Description Advanced** Power-On Options Allows you to set: ● POST Mode (QuickBoot, FullBoot, or FullBoot every 1-30 days). ● POST Messages (Enable or Disable). ● F9 Prompt (Enable or Disable). Enabling this feature displays F9=Boot Menu during POST. Disabling this feature prevents the text from being displayed. However, pressing the F9 key still accesses the boot menu. ● F10 Prompt (Enable or Disable)-Enabling this feature displays F10=Setup during POST. Disabling this feature prevents the text from being displayed, but pressing F10 still accesses the Setup screen. ● F11 Prompt (Enable or Disable)-Makes the Factory Recovery option visible during POST. Disabling this feature prevents the text from being displayed, but pressing F10 still accesses the Setup screen. Factory Recovery Boot Support must be enabled to use this option. ● F12 Prompt (Enable or Disable)-Enabling this feature displays F12=Network Service Boot during POST. Disabling this feature prevents the text from being displayed but pressing F12 still forces the system to attempt booting from the network. ● Factory Recovery Boot Support (Enable or Disable)-Recovery partition hard disk drive (HDD) option available. Vista leaves the factory with this support in place. ● Option ROM prompt* (Enable or Disable)-Enabling this feature causes the system to display a message before loading options ROMs. ● Remote Wakeup Boot Source ● After Power Loss (On or Off)-Enabling this option directs the previous state to be the default. ● POST Delay (in seconds) (Enable or Disable)-Enabling this feature adds a user-specified delay to the POST process. This delay is sometimes needed for hard drives on some PCI cards that spin up slowly (so slowly that they are not ready to boot by the time POST is finished). The POST delay also gives you more time to select F10 to enter the Computer Setup (F10) Utility. ● Limit (CPUID Maximum Value to 3) (Enable/Disable) Execute Memory Test Tests workstation memory. The workstation reboots, and any changes that have been made are lost. The workstation might boot with memory in a sub optimal configuration. BIOS Power-On Enables you to disable or specify a weekday and time for BIOS power-on. Onboard Devices Enables you to set resources for or disable onboard system devices such as serial ports, parallel ports, and diskette controllers. Operating system parameters generally override Onboard Devices settings. PCI Devices Enables you to set the IRQ for or disable the following devices during POST: ● Intel USB controllers ● Intel HD audio device ● Intel RAID controller ● nVidia VGA controller ● Broadcom Ethernet controller Operating system parameters generally override PCI Devices settings. Available IRQ values are 5, 10, and 11. ENWW Computer Setup (F10) Utility 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
Heading
Option
Description
Advanced**
Power-On
Options
Allows you to set:
●
POST Mode (QuickBoot, FullBoot, or FullBoot every 1–30 days).
●
POST Messages (Enable or Disable).
●
F9 Prompt (Enable or Disable). Enabling this feature displays
F9=Boot Menu
during POST.
Disabling this feature prevents the text from being displayed. However, pressing the F9 key
still accesses the boot menu.
●
F10 Prompt (Enable or Disable)—Enabling this feature displays
F10=Setup
during POST.
Disabling this feature prevents the text from being displayed, but pressing F10 still accesses
the Setup screen.
●
F11 Prompt (Enable or Disable)—Makes the Factory Recovery option visible during POST.
Disabling this feature prevents the text from being displayed, but pressing F10 still accesses
the Setup screen. Factory Recovery Boot Support must be enabled to use this option.
●
F12 Prompt (Enable or Disable)—Enabling this feature displays
F12=Network Service Boot
during POST. Disabling this feature prevents the text from being displayed but pressing F12
still forces the system to attempt booting from the network.
●
Factory Recovery Boot Support (Enable or Disable)—Recovery partition hard disk drive
(HDD) option available. Vista leaves the factory with this support in place.
●
Option ROM prompt* (Enable or Disable)—Enabling this feature causes the system to display
a message before loading options ROMs.
●
Remote Wakeup Boot Source
●
After Power Loss (On or Off)—Enabling this option directs the previous state to be the default.
●
POST Delay (in seconds) (Enable or Disable)—Enabling this feature adds a user-specified
delay to the POST process. This delay is sometimes needed for hard drives on some PCI
cards that spin up slowly (so slowly that they are not ready to boot by the time POST is
finished). The POST delay also gives you more time to select F10 to enter the Computer
Setup (F10) Utility.
●
Limit (CPUID Maximum Value to 3) (Enable/Disable)
Execute
Memory Test
Tests workstation memory. The workstation reboots, and any changes that have been made are
lost. The workstation might boot with memory in a sub optimal configuration.
BIOS Power-On
Enables you to disable or specify a weekday and time for BIOS power-on.
Onboard
Devices
Enables you to set resources for or disable onboard system devices such as serial ports, parallel
ports, and diskette controllers. Operating system parameters generally override Onboard Devices
settings.
PCI Devices
Enables you to set the IRQ for or disable the following devices during POST:
●
Intel USB controllers
●
Intel HD audio device
●
Intel RAID controller
●
nVidia VGA controller
●
Broadcom Ethernet controller
Operating system parameters generally override PCI Devices settings.
Available IRQ values are 5, 10, and 11.
Table 4-1
Computer Setup (F10) Utility menu descriptions (continued)
ENWW
Computer Setup (F10) Utility
31