HP Xw4600 HP xw4600 Workstation - Service and Technical Reference Guide - Page 89

Installing a PCI Express card - graphics card

Get HP Xw4600 - Workstation - 2 GB RAM PDF manuals and user guides
UPC - 883585516483
View all HP Xw4600 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

2. Open the PCI card retention clamp. Press the retention clamp levers down to unsnap, and then rotate them up (1). Figure 5-28 Removing a PCI Express card 3. If removing a PCI Express x16 graphics card, press in on the release lever (2) while lifting the card (3) out of the chassis. Store the card in an anti-static bag. If removing s PCI Express card without a release lever, simply lift the card out of the chassis. 4. Install a PCI slot cover and close the PCI retention clamp. If the PCI retention clamp levers do not close, ensure that all cards are properly seated, and then try again. Installing a PCI Express card To install a PCI Express card: 1. Disconnect power from the system (Predisassembly procedures on page 57), remove the side access panel (Removing the side access panel on page 61), and remove the PCI retainer (PCI card support bracket on page 76), if installed. ENWW Removing and replacing components 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
2.
Open the PCI card retention clamp. Press the retention clamp levers down to unsnap, and then
rotate them up (1).
Figure 5-28
Removing a PCI Express card
3.
If removing a PCI Express x16 graphics card, press in on the release lever (2) while lifting the card
(3) out of the chassis. Store the card in an anti-static bag.
If removing s PCI Express card without a release lever, simply lift the card out of the chassis.
4.
Install a PCI slot cover and close the PCI retention clamp. If the PCI retention clamp levers do not
close, ensure that all cards are properly seated, and then try again.
Installing a PCI Express card
To install a PCI Express card:
1.
Disconnect power from the system (
Predisassembly procedures
on page
57
), remove the side
access panel (
Removing the side access panel
on page
61
), and remove the PCI retainer (
PCI
card support bracket
on page
76
), if installed.
ENWW
Removing and replacing components
79