JVC GY-HM620U Instruction Manual - Page 181

List of Live Streaming Error Displays, Blinking of the Tally Lamp

Get JVC GY-HM620U PDF manuals and user guides View all JVC GY-HM620U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 181 highlights

List of Live Streaming Error Displays a The following error messages are displayed when the live streaming setting is incorrect, or when the connection is lost during live streaming. Error message Invalid Address Multicast Is Not Supported Cannot Connect to Receiver TCP Disconnected Not Enough Bandwidth Connection Timeout Authorization Failed Connection Error Disconnected Status 0 The IP address format is incorrect. 0 The domain name cannot be converted into the IP address. Action 0 Enter the IP address or host name of the destination correctly. (A P176 [Setting Distribution] ) An IP multicast address was set. Establishment of connection with TCP failed. Use an IP address that is not a multicast address. 0 Ensure that the recipient's device is set to TCP. 0 Set Type to "MPEG2-TS/UDP". (A P176 [Setting Distribution] ) TCP connection is lost. Check to ensure that there is no abnormality in the decoder, or network connection device and cables, followed by establishing the connection again. 0 The communication bandwidth 0 Lower the resolution/picture is narrower than the average bit quality of the video to be rate. 0 The network bandwidth is distributed. 0 Consider switching to the use of insufficient, and packets are a stable network, such as wired discarded. LAN. Timeout for connection via ZIXI. Set [Destination Address] and [Destination Port] correctly. (A P176 [Setting Distribution] ) Authentication of connection via ZIXI failed. Set [Stream ID] and [Password] correctly. (A P176 [Setting Distribution] ) Connection via "ZIXI" or "RTMP" failed. Check whether a different camera with an identical stream ID is connected. 0 Set [Destination URL] and [Stream Key] correctly. (A P123 [ Destination URL ] ) (A P123 [ Stream Key ] ) "ZIXI" or "RTMP" connection is lost. Check whether there is abnormality with the network connection device, cables, etc., and try to re-establish the connection. Others Blinking of the Tally Lamp The tally lamp start blinking when the remaining space on the SD card is running out during recording, or when the battery power is running low. Blinking Mode Blinks slowly (once every second) Blinks quickly (2 times per second) Remaining Battery Power/SD Card Space 0 Battery power is low 0 Remaining recording time on SD card is less than 3 minutes (during recording) 0 When a malfunction occurred during live streaming a 0 Remaining battery power is almost zero 0 Remaining recording time on SD card is zero (during recording) 0 Error on the camera recorder 181

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
List of Live Streaming Error Displays
a
The following error messages are displayed when the live streaming setting is incorrect, or when the
connection is lost during live streaming.
Error message
Status
Action
Invalid Address
0
The IP address format is
incorrect.
0
The domain name cannot be
converted into the IP address.
0
Enter the IP address or host
name of the destination
correctly.
(
A
P176 [Setting Distribution] )
Multicast Is Not Supported
An IP multicast address was set.
Use an IP address that is not a
multicast address.
Cannot Connect to Receiver
Establishment of connection with
TCP failed.
0
Ensure that the recipient’s
device is set to TCP.
0
Set Type to “MPEG2-TS/UDP”.
(
A
P176 [Setting Distribution] )
TCP Disconnected
TCP connection is lost.
Check to ensure that there is no
abnormality in the decoder, or
network connection device and
cables, followed by establishing the
connection again.
Not Enough Bandwidth
0
The communication bandwidth
is narrower than the average bit
rate.
0
The network bandwidth is
insufficient, and packets are
discarded.
0
Lower the resolution/picture
quality of the video to be
distributed.
0
Consider switching to the use of
a stable network, such as wired
LAN.
Connection Timeout
Timeout for connection via ZIXI.
Set [Destination Address] and
[Destination Port] correctly.
(
A
P176 [Setting Distribution] )
Authorization Failed
Authentication of connection via
ZIXI failed.
Set [Stream ID] and [Password]
correctly.
(
A
P176 [Setting Distribution] )
Connection Error
Connection via “ZIXI” or “RTMP”
failed.
Check whether a different camera
with an identical stream ID is
connected.
0
Set [Destination URL] and
[Stream Key] correctly.
(
A
P123 [ Destination URL ] )
(
A
P123 [ Stream Key ] )
Disconnected
“ZIXI” or “RTMP” connection is lost.
Check whether there is abnormality
with the network connection device,
cables, etc., and try to re-establish
the connection.
Blinking of the Tally Lamp
The tally lamp start blinking when the remaining space on the SD card is running out during recording, or
when the battery power is running low.
Blinking Mode
Remaining Battery Power/SD Card Space
Blinks slowly
(once every second)
0
Battery power is low
0
Remaining recording time on SD card is less than 3 minutes (during
recording)
0
When a malfunction occurred during live streaming
a
Blinks quickly
(2 times per second)
0
Remaining battery power is almost zero
0
Remaining recording time on SD card is zero (during recording)
0
Error on the camera recorder
181
Others