Netgear FS728TLP Web Management User Guide - Page 184

Use the ACL Wizard to Create an ACL Based on a Source IP Address

Get Netgear FS728TLP PDF manuals and user guides View all Netgear FS728TLP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 184 highlights

ProSAFE FS526Tv2, FS726Tv2, and FS728TLP Smart Switches 11. (Optional) In the Sequence Number field, enter a number in the range from 1 to 4,294,967,295. The sequence number specifies the order of the ACL relative to existing ACLs that are bound to the same interface or interfaces. A lower number specifies a higher precedence order. If a sequence number is already in use for the port or ports, the ACL replaces the existing ACL that uses the same sequence number. If you do not enter a number, the smart switch assigns a default sequence number automatically. 12. In the Port Selection Table section, click one or both of the orange bars: • PORT. Displays the physical ports. • LAG. Displays the link aggregation groups 1 through 8. (For more information, see Chapter 8, Configure LAGs and LAG Membership.) 13. To bind one or more ports or LAGs to the ACL, use one of the following methods: • Bind individual ports or LAGs to the MAC ACL: a. Click the PORT or LAG orange bar. b. Below each selected orange bar, select one or more ports or LAGs by clicking the square below each port or LAG. (Clicking a second time removes the ports or LAGs from the binding.) • Bind all ports or LAGs to the MAC ACL. In the orange bar, click the square next to PORT or LAG. All ports or LAGs are bound to the MAC ACL. (Clicking a second time removes all ports or LAGs from the binding.) 14. Click the Apply button. The settings are saved, and the ACL information is added to both the Interface Binding Status table and the MAC Binding Table on the MAC Binding Table screen (see View the MAC ACL Binding Table on page 206). For information about how to change the rule or remove the rule, see the procedures at the end of Manage MAC ACL Rules on page 199. Use the ACL Wizard to Create an ACL Based on a Source IP Address Before you can use the ACL Wizard to create an ACL that is based on a source address, first create an IP ACL ID.  To create an IP ACL ID and use the ACL Wizard to configure a rule that is based on the source IP address: 1. Select Security > ACL > Advanced > IP ACL. Manage Access Control Lists 184

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
  • 260
  • 261
  • 262
  • 263
  • 264
  • 265
  • 266
  • 267
  • 268
  • 269
  • 270
  • 271
  • 272
  • 273
  • 274
  • 275
  • 276
  • 277
  • 278
  • 279
  • 280
  • 281
  • 282
  • 283
  • 284
  • 285
  • 286
  • 287
  • 288
  • 289
  • 290
  • 291
  • 292
  • 293
  • 294
  • 295
  • 296
  • 297
  • 298
  • 299
  • 300
  • 301
  • 302
  • 303
  • 304
  • 305
  • 306
  • 307
  • 308
  • 309
  • 310
  • 311
  • 312
  • 313
  • 314
  • 315
  • 316
  • 317
  • 318
  • 319
  • 320
  • 321
  • 322
  • 323
  • 324
  • 325
  • 326
  • 327
  • 328
  • 329
  • 330
  • 331
  • 332
  • 333
  • 334
  • 335
Manage Access Control Lists
184
ProSAFE FS526Tv2, FS726Tv2, and FS728TLP Smart Switches
11.
(Optional) In the Sequence Number field, enter a number in the range from 1 to
4,294,967,295.
The sequence number specifies the order of the ACL relative to existing ACLs that are
bound to the same interface or interfaces. A lower number specifies a higher precedence
order. If a sequence number is already in use for the port or ports, the ACL replaces the
existing ACL that uses the same sequence number. If you do not enter a number, the
smart switch assigns a default sequence number automatically.
12.
In the Port Selection Table section, click one or both of the orange bars:
•
PORT
. Displays the physical ports.
•
LAG
. Displays the link aggregation groups 1 through 8. (For more information, see
Chapter 8, Configure LAGs and LAG Membership
.
)
13.
To bind one or more ports or LAGs to the ACL, use one of the following methods:
•
Bind individual ports or LAGs to the MAC ACL:
a.
Click the
PORT
or
LAG
orange bar.
b.
Below each selected orange bar, select one or more ports or LAGs by clicking
the square below each port or LAG.
(Clicking a second time removes the ports or LAGs from the binding.)
•
Bind all ports or LAGs to the MAC ACL
. In the orange bar, click the square next to
PORT or LAG. All ports or LAGs are bound to the MAC ACL.
(Clicking a second time removes all ports or LAGs from the binding.)
14.
Click the
Apply
button.
The settings are saved, and the ACL information is added to both the Interface Binding
Status table and the MAC Binding Table on the MAC Binding Table screen (see
View the
MAC ACL Binding Table
on page
206).
For information about how to change the rule or remove the rule, see the procedures at the
end of
Manage MAC ACL Rules
on page
199.
Use the ACL Wizard to Create an ACL Based on a Source
IP Address
Before you can use the ACL Wizard to create an ACL that is based on a source address, first
create an IP ACL ID.
To create an IP ACL ID and use the ACL Wizard to configure a rule that is based on the
source IP address:
1.
Select
Security > ACL > Advanced > IP ACL
.