Sony SNCEP520 User Manual (SNC-ER/EP User Guide) - Page 50

Administrating the Camera

Setting the Camera Image and Audio — Camera Menu

50

Notes

•

The actual frame rate and bit rate may be different

depending on the image size, shooting scene, or

network condition.

• When

Adaptive rate control

is set to

On

, the actual

frame rate and bit rate change within the range that

does not exceed the values set in

Frame rate

and

Bit

rate

.

•

When setting Image 2, set the frame rate of Image 1 to

15 fps or less. (SNC-EP520/EP521/ER520/ER521)

Image quality

Set the JPEG image quality.

Selectable values are from

Level 1

to

Level 10

.

When

Level 10

is selected, the best image quality is

achieved.

Bandwidth control

Limits the network bandwidth for the JPEG image data

output from the camera.

Note

Audio may be interrupted depending on the selected

bandwidth. In this case, select a wider bandwidth.

OK/Cancel

See “Buttons common to every menu” on page 35.

Streaming Tab

Use this tab to set the items for the transmission by

unicast or multicast.

Unicast streaming

Specify the transmission port numbers of the MPEG4/

H.264 video data and audio data to be used when

Unicast

is selected from the

Connection

drop-down list

in the

Other

panel on the main viewer.

Video port number 1, 2

Specify the transmission port number of the MPEG4/

H.264 video data. It is initially set to 50000. Specify an

even number from 1024 to 65534. Two port numbers

(the number specified here and an odd number with 1

added to the specified number) are actually used for

video data communication and control.

The setting for Image 1 and Image 2 apply for Video port

number 1 and 2 respectively.

Audio port number

Specify the transmission port number of the audio data.

It is initially set to 50002. Specify an even number from

1024 to 65534. Two port numbers (the number specified

here and an odd number with 1 added to the specified

number) are used for audio data communication and

control.

Note

Specify different numbers for the video port number and

the audio port number.

Multicast streaming

Set whether the camera uses multicast streaming for

MPEG4/H.264 video data and audio data or not. It

reduces the transmission load on the camera by having a

computer of the same segment network receive the same

transmitting data.

Select

On

to allow, or

Off

not to allow multicast

sending.

When you select

On

, set

Multicast address

,

Video port

number

and

Audio port number

properly.

Multicast address

Type the multicast address used on the multicast

streaming.

Video port number 1, 2

Specify the MPEG4/H.264 video transmission port

number used for the multicast streaming. It is initially

set to 60000. Specify an even number from 1024 to

65534. Two port numbers (the number specified here

and an odd number with 1 added to the specified

number) are used for video data communication and

control.

The setting for Image 1 and Image 2 apply for Video port

number 1 and 2 respectively.

Audio port number

Specify the audio transmission port number used for the

multicast streaming. It is initially set to 60002. Specify

an even number from 1024 to 65534. Two port numbers

(the number specified here and an odd number with 1

added to the specified number) are used for audio data

communication and control.

Note

Specify different numbers for the video port number and

the audio port number.

OK/Cancel

See “Buttons common to every menu” on page 35.

Section	Page
Table of Contents	2
Overview	4
Features	4
How to Use This User’s Guide	5
System Requirements	6
Preparation	7
Assigning the IP Address to the Camera	7
Assigning an IP address using SNC toolbox	7
When using Windows XP Service Pack 2 or later	9
When using Windows Vista	11
When using Windows 7	14
Accessing the Camera Using the Web Browser	16
Basic Configuration by the Administrator	19
Operating the Camera	20
Administrator and User	20
Logging in to System	21
Logging in as a user	21
About Viewers	21
Configuration of Main Viewer	22
Main menu	22
Control panel section	22
Monitor image	25
Plug-in free viewer	25
Operating the Camera	26
Controlling via the control panel (Operation common to Area zoom mode and Vector dragging mode)	26
Panning and tilting by clicking the monitor image (Area zoom mode only)	27
Panning, tilting and zooming by specifying the area (Area zoom mode only)	27
Panning and tilting by dragging the screen (Vector dragging mode only)	27
Moving the camera to a preset position (Common operations in Area zoom and Vector dragging modes)	28
Using pan/tilt/zoom operations with the displayed control bar (PTZ Control bar only)	28
Controlling the Camera on a Panorama Image	28
Facing the camera toward a specified point	28
Using the Trigger Button	29
Sending a monitor image via e-mail	29
Sending a monitor image to an FTP server	29
Recording a camera image as a still image	29
Controlling alarm output 1	30
Controlling the Day/Night function	30
Playing an audio file stored in the camera	30
Switching Transmission Mode	30
Using the System Utility	31
SNC viewer	31
SNC desktop viewer	33
Administrating the Camera	35
Basic Operations of the Administrator Menu	35
How to set up the Administrator menu	35
Configuration of the Administrator menu	36
Configuring the System - System Menu	37
System Tab	37
Date & time Tab	38
Superimpose Tab	39
Installation Tab	40
Initialize Tab	41
System log Tab	43
Access log Tab	43
Setting the Camera Image and Audio - Camera Menu	43
Common Tab	43
Picture Tab	44
Privacy Masking tab	46
Day/Night Tab	48
Video codec Tab	48
Streaming Tab	50
Configuring the Network - Network Menu	51
Network Tab	51
QoS Tab	52
Dynamic IP address notification Tab - Notifying the IP Address	54
Setting the SSL function - SSL Menu	56
SSL tab	56
CA certificate tab - Adding the CA certificate for client authentication	58
How to install the CA certificate	58
To remove an installed CA certificate	60
Using the 802.1X Authentication Function - 802.1X Menu	61
System configuration of 802.1X network	61
Common Tab - Basic setting of 802.1X authentication function	61
Client certificate Tab	62
CA certificate Tab	63
Setting the 802.1X authentication function - Example of Windows Server 2003	63
Setting the User - User Menu	66
Setting the Security - Security Menu	67
Saving the Camera Position and Action - Preset position Menu	68
Position Tab - Saving pan/tilt/ zoom position	68
Position Tour Tab - Setting a position tour	69
Sending an Image via E-mail - e-Mail (SMTP) Menu	70
Common Tab - Setting the e-Mail (SMTP) Function	70
Alarm sending Tab - Setting the e-mail sending mode when detecting the alarm	72
Periodical sending Tab - Setting the periodical e-mail sending mode	73
Abnormal sending tab - Setting the abnormal e-mail sending mode	73
Sending Images to FTP Server - FTP client Menu	74
Common Tab - Setting the FTP client function	74
Alarm sending Tab - Setting the FTP client action when detecting the alarm	74
Periodical sending Tab - Setting the periodical FTP client activity	75
Recording Images in Memory - Image memory Menu	77
Common Tab - Setting the image memory function	77
Alarm recording Tab - Setting the Image memory function when detecting the alarm	78
Periodical recording Tab - Setting the periodical recording mode	79
Folder structure of Image memory	80
Downloading Images from the Camera - FTP server Menu	81
Setting the Edge Storage - Edge Storage Menu	81
Folder structure of Edge Storage	83
Setting the Alarm Output - Alarm output Menu	83
Alarm output 1 Tab	83
Outputting Audio Linked to Alarm Detection - Voice alert Menu	84
Voice alert 1, 2, 3 Tab	84
Setting the Operations from the Viewer - Trigger Menu	85
Setting the Schedule - Schedule Menu	87
Setting the Alarm Buffer - Alarm buffer Menu	88
Setting the Sensor input/ Camera tampering detection/Motion detection - Event detection menu	88
Sensor input tab - Set the sensor input	88
Camera tampering detection tab - Set the camera tampering detection	89
Motion detection tab - Set the motion detection	89
Setting items for motion detection	89
Configuring the Viewer - Viewer Menu	91
Layout tab	91
HTML output tab	94
Others	95
Using the SNC toolbox	95
Starting SNC toolbox	95
How to use SNC toolbox	95
Registering in My device	97
Changing the Device list display method	98
Setting SNC toolbox options	99
Using Privacy Masking - Masking a Camera Image	100
Using Panorama Creator - Creating a Panorama Image	102
Using the Custom Homepage - Setting the customized homepage	103
Using the Firmware Upgrade	104
Using the Schedule Task	104
Configuring the device setting	106
Device restart and initialization	108
Using the SNC audio upload tool - Transmitting Audio to Camera	108
Installing the SNC audio upload tool	109
Connecting the Camera to the Computer	109
Using the SNC audio upload tool	110
Using the SNC video player - Playing a Video/ Audio File Recorded with the Camera	114
Installing the SNC video player	114
Using the SNC video player	115
Using the SNMP	116
1. Inquiry Commands	116
2. Setting Commands	116
Glossary	117

Sony SNCEP520 User Manual (SNC-ER/EP User Guide) - Page 50

Streaming Tab, OK/Cancel, Unicast streaming

Page 50 highlights