Oki B930dn User Guide (English) - Page 89

Target Computers, Interface, Set Up Procedure, Daemon Protocol. Lpd Tcp/ip Unix

Get Oki B930dn PDF manuals and user guides View all Oki B930dn manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

The printer LPD supports Spool Mode where print jobs from clients are spooled once before output and Non-spool Mode where print jobs are sequentially output without spooling. LPD (TCP/IP) NOTE When the LPD port is used, the printer can limit print instructions by IP addresses. TARGET COMPUTERS The target computers are as follows: • Workstation or personal computer with RFC 1179 Line Printer Daemon Protocol. LPD (TCP/IP) UNIX INTERFACE The printer LPD is available on the following interfaces: • Ethernet 100BaseTX • Ethernet 10Base-T The applicable frame types conform to Ethernet II. SET UP PROCEDURE The setting procedure is as follows: 1. Setting up the printer Set the IP address on the printer Operator Panel. Use the printer Operator Panel or the EWS to set the LPD port to [Enable] (default: [Enable]). NOTE > Before activating the LPD port, set the IP address of the printer. For details on how to set the IP address and the port, refer Printer Configuration. B930n User's Guide> 83

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
B930n User’s Guide> 83
The printer LPD supports Spool Mode where print jobs from clients
are spooled once before output and Non-spool Mode where print
jobs are sequentially output without spooling.
NOTE
When the LPD port is used, the printer can limit print instructions
by IP addresses.
TARGET COMPUTERS
The target computers are as follows:
•
Workstation or personal computer with RFC 1179 Line Printer
Daemon Protocol. LPD (TCP/IP) UNIX
INTERFACE
The printer LPD is available on the following interfaces:
•
Ethernet 100BaseTX
•
Ethernet 10Base-T
The applicable frame types conform to Ethernet II.
SET UP PROCEDURE
The setting procedure is as follows:
1.
Setting up the printer
Set the IP address on the printer Operator Panel.
Use the printer Operator Panel or the EWS to set the LPD port
to [Enable] (default: [Enable]).
NOTE
>
Before activating the LPD port, set the IP address of the
printer. For details on how to set the IP address and the
port, refer Printer Configuration.
LPD (TCP/IP)