Dell PowerEdge R750xa EMC Installation and Service Manual - Page 106

Replacing the GPU bracket

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

Figure 100. Installing the R3 paddle card Next steps 1. Insert the paddle card slimline cable into the cable access latch on cooling fan cage and also through the air shroud notch. 2. If removed, install the rear mounting front PERC module. 3. Follow the procedure listed in After working inside your system. Replacing the GPU bracket Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If installing a new GPU card, unpack it and prepare the card for installation. NOTE: For instructions, see the documentation accompanying the card. 4. New GPU cards are shipped with standard bracket, replace it with a custom bracket before installing. NOTE: Based on the GPU card, use the appropriate custom bracket. Steps 1. Using Torx #T15 screwdriver loosen the torx screws and remove the standard bracket from the GPU card. 106 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Figure 100. Installing the R3 paddle card
Next steps
1.
Insert the paddle card slimline cable into the cable access latch on cooling fan cage and also through the air shroud notch.
2.
If removed,
install the rear mounting front PERC module
.
3.
Follow the procedure listed in
After working inside your system
.
Replacing the GPU bracket
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If installing a new GPU card, unpack it and prepare the card for installation.
NOTE:
For instructions, see the documentation accompanying the card.
4.
New GPU cards are shipped with standard bracket, replace it with a custom bracket before installing.
NOTE:
Based on the GPU card, use the appropriate custom bracket.
Steps
1.
Using Torx #T15 screwdriver loosen the torx screws and remove the standard bracket from the GPU card.
106
Installing and removing system components