Dell PowerEdge R750xa EMC Installation and Service Manual - Page 156

Installing the system board

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 156 highlights

Figure 167. Installing the system board Next steps 1. Replace the following components: a. Trusted Platform Module (TPM) NOTE: The TPM Module must be replaced only while installing new system board. b. IDSDM module (if removed) c. Internal USB card (if removed) d. OCP card (if removed) e. Intrusion switch module f. Processor and heat sink or Liquid cooling module g. Memory modules h. BOSS S2 module (if, removed) i. Serial COM port (if removed) j. VGA port (if removed) k. R1 and R4 paddle card l. R3 paddle card (If removed) m. Expansion card riser n. Side wall bracket o. Cooling fan cage assembly p. Air shroud q. Power supply units (PSU) 2. Reconnect all cables to the system board. NOTE: Ensure that the cables inside the system are routed along the chassis wall and secured using the cable securing bracket. 3. Ensure that you perform the following steps: a. Use the Easy Restore feature to restore the Service Tag. See the Restoring the system by using the Easy Restore feature section. b. If the service tag is not backed up in the backup flash device, enter the system service tag manually. See the Manually update the Service Tag by using System Setup section. c. Update the BIOS and iDRAC versions. NOTE: Reenable the Trusted Platform Module (TPM). See the Upgrading the Trusted Platform Module section. 4. If you are not using Easy restore, import your new or existing iDRAC Enterprise license. For more information, see the iDRAC User's Guide available at https://www.dell.com/idracmanuals . 5. Follow the procedure listed in After working inside your system. 156 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Figure 167. Installing the system board
Next steps
1.
Replace the following components:
a.
Trusted Platform Module (TPM)
NOTE:
The TPM Module must be replaced only while installing new system board.
b.
IDSDM module (if removed)
c.
Internal USB card (if removed)
d.
OCP card (if removed)
e.
Intrusion switch module
f.
Processor and heat sink
or
Liquid cooling module
g.
Memory modules
h.
BOSS S2 module (if, removed)
i.
Serial COM port (if removed)
j.
VGA port (if removed)
k.
R1 and R4 paddle card
l.
R3 paddle card (If removed)
m.
Expansion card riser
n.
Side wall bracket
o.
Cooling fan cage assembly
p.
Air shroud
q.
Power supply units (PSU)
2.
Reconnect all cables to the system board.
NOTE:
Ensure that the cables inside the system are routed along the chassis wall and secured using the cable securing
bracket.
3.
Ensure that you perform the following steps:
a.
Use the Easy Restore feature to restore the Service Tag. See the
Restoring the system by using the Easy Restore
feature
section.
b.
If the service tag is not backed up in the backup flash device, enter the system service tag manually. See the Manually
update the Service Tag by using System Setup section.
c.
Update the BIOS and iDRAC versions.
NOTE:
Reenable the Trusted Platform Module (TPM). See the
Upgrading the Trusted Platform Module
section.
4.
If you are not using Easy restore, import your new or existing iDRAC Enterprise license. For more information, see the
iDRAC
User's Guide
available at
.
5.
Follow the procedure listed in
After working inside your system
.
156
Installing and removing system components