Dell PowerEdge R750xa EMC Installation and Service Manual - Page 43

Side wall brackets, Removing the side wall bracket

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 43 highlights

Figure 36. Installing a cooling fan Next steps 1. Follow the procedure listed in After working inside your system. Side wall brackets Removing the side wall bracket There are two side wall brackets on either side of the system. The procedure to remove them is same. Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. If required, remove the drive backplane cover. 4. If installed, remove the air shroud. 5. Remove the cooling fan cage assembly. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. Route the cable properly when you replace it to prevent the cable from being pinched or crimped. Steps 1. Press the blue side tabs to release the side wall cable holder. NOTE: Move the cables out of the side wall cable holder. 2. Press the center tab to release the bracket from the system, and lift it away from the system. Installing and removing system components 43

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Figure 36. Installing a cooling fan
Next steps
1.
Follow the procedure listed in
After working inside your system
.
Side wall brackets
Removing the side wall bracket
There are two side wall brackets on either side of the system. The procedure to remove them is same.
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
If required,
remove the drive backplane cover
.
4.
If installed,
remove the air shroud
.
5.
Remove the cooling fan cage assembly
.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. Route the cable
properly when you replace it to prevent the cable from being pinched or crimped.
Steps
1.
Press the blue side tabs to release the side wall cable holder.
NOTE:
Move the cables out of the side wall cable holder.
2.
Press the center tab to release the bracket from the system, and lift it away from the system.
Installing and removing system components
43