Dell PowerEdge R750xa EMC Installation and Service Manual - Page 116

Removing the NVLink bridges, Installing the NVLink sponge

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 116 highlights

Figure 114. Installing the NVLink sponge Next steps 1. Install the rear mounting front PERC module. 2. Follow the procedure listed in After working inside your system. Removing the NVLink bridges Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the rear mounting front PERC module. NOTE: Observe the cable routing before disconnecting the cables. 4. Remove the NVLink sponges. 5. Remove the GPU riser module. 6. Number of NVLink bridges vary as per the GPU. 7. Slot priority for GPU card installation without NVLink bridges: slot 31, slot 33, slot 34, and slot 32. 8. Slot priority for GPU card installation with NVLink bridges: slot 33, slot 34, slot 31, and slot 32. NOTE: For more information about supported GPU cards and their slot priority, see expansion card installation guidelines. Steps 1. Holding the edges, pull the NVLink bridges out of the GPU cards. 116 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Figure 114. Installing the NVLink sponge
Next steps
1.
Install the rear mounting front PERC module
.
2.
Follow the procedure listed in
After working inside your system
.
Removing the NVLink bridges
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the rear mounting front PERC module
.
NOTE:
Observe the cable routing before disconnecting the cables.
4.
Remove the NVLink sponges
.
5.
Remove the GPU riser module
.
6.
Number of NVLink bridges vary as per the GPU.
7.
Slot priority for GPU card installation without NVLink bridges: slot 31, slot 33, slot 34, and slot 32.
8.
Slot priority for GPU card installation with NVLink bridges: slot 33, slot 34, slot 31, and slot 32.
NOTE:
For more information about supported GPU cards and their slot priority, see
expansion card installation guidelines
.
Steps
1.
Holding the edges, pull the NVLink bridges out of the GPU cards.
116
Installing and removing system components