Dell PowerEdge R750xa EMC Installation and Service Manual - Page 44

Installing the side wall bracket

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Figure 37. Removing the side wall bracket Next steps 1. Replace the side wall bracket. Installing the side wall bracket There are two side wall brackets on either side of the system. The procedure to install them is same. Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. If required, remove the drive backplane cover. 4. If installed, remove the air shroud. 5. Remove the cooling fan cage assembly. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. Route the cable properly when you replace it to prevent the cable from being pinched or crimped. Steps 1. Align the guide slots on the side wall bracket with the guides on the system and slide until the cover is seated firmly. NOTE: Route the cables through the side wall cable holder. 2. Close the side wall cable holder until the holder clicks into place. 44 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Figure 37. Removing the side wall bracket
Next steps
1.
Replace the side wall bracket
.
Installing the side wall bracket
There are two side wall brackets on either side of the system. The procedure to install them is same.
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
If required,
remove the drive backplane cover
.
4.
If installed,
remove the air shroud
.
5.
Remove the cooling fan cage assembly
.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. Route the cable
properly when you replace it to prevent the cable from being pinched or crimped.
Steps
1.
Align the guide slots on the side wall bracket with the guides on the system and slide until the cover is seated firmly.
NOTE:
Route the cables through the side wall cable holder.
2.
Close the side wall cable holder until the holder clicks into place.
44
Installing and removing system components