Dell PowerEdge R750xa EMC Installation and Service Manual - Page 138

Connecting the BOSS S2 power and signal cables to the BOSS S2 module,

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

2. Follow the procedure listed in the Before working inside your system. Steps 1. Connect the BOSS S2 power and signal cables to the connectors on the BOSS S2 module. Figure 145. Connecting the BOSS S2 power and signal cables to the BOSS S2 module 2. Align the BOSS S2 module at an angle with the controller card module slot. 3. Insert the BOSS S2 module and push the module horizontally towards the rear of the system until firmly seated. 4. Using the Phillips #1 screwdriver, secure the BOSS S2 module with the M3 x 0.5 x 4.5 mm screw. 5. Connect the BOSS S2 power and signal cable to the connectors on the system board. Figure 146. Installing the BOSS S2 module 6. Align the M.2 SSD at an angle with the BOSS S2 card carrier. 7. Insert the M.2 SSD until it is firmly seated in the BOSS S2 card carrier. 138 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
2.
Follow the procedure listed in the
Before working inside your system
.
Steps
1.
Connect the BOSS S2 power and signal cables to the connectors on the BOSS S2 module.
Figure 145. Connecting the BOSS S2 power and signal cables to the BOSS S2 module
2.
Align the BOSS S2 module at an angle with the controller card module slot.
3.
Insert the BOSS S2 module and push the module horizontally towards the rear of the system until firmly seated.
4.
Using the Phillips #1 screwdriver, secure the BOSS S2 module with the M3 x 0.5 x 4.5 mm screw.
5.
Connect the BOSS S2 power and signal cable to the connectors on the system board.
Figure 146. Installing the BOSS S2 module
6.
Align the M.2 SSD at an angle with the BOSS S2 card carrier.
7.
Insert the M.2 SSD until it is firmly seated in the BOSS S2 card carrier.
138
Installing and removing system components