Dell PowerEdge R750xa EMC Installation and Service Manual - Page 126

Installing the VGA port, Connecting the VGA port cable

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 126 highlights

Figure 129. Installing the VGA port 3. Connect the VGA port cable to the LC rear I/O board. 4. Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board. 5. Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated on the system board connector. 6. Tighten the captive screws on the system. Figure 130. Connecting the VGA port cable Next steps 1. Install the air shroud. 2. Follow the procedure listed in After working inside your system. 126 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Figure 129. Installing the VGA port
3.
Connect the VGA port cable to the LC rear I/O board.
4.
Holding the edges or the touch points, align the holes on the expansion card riser with the guides on the system board.
5.
Lower the expansion card riser into place and press the touch points until the expansion card riser connector is fully seated
on the system board connector.
6.
Tighten the captive screws on the system.
Figure 130. Connecting the VGA port cable
Next steps
1.
Install the air shroud
.
2.
Follow the procedure listed in
After working inside your system
.
126
Installing and removing system components