Dell PowerEdge R750xa EMC Installation and Service Manual - Page 124

Optional VGA port for liquid cooling module, Removing the VGA port

Get Dell PowerEdge R750xa PDF manuals and user guides View all Dell PowerEdge R750xa manuals
Add to My Manuals
Save this manual to your list of manuals

Page 124 highlights

Optional VGA port for liquid cooling module Removing the VGA port The procedure to remove VGA port from Riser 2 is same. Prerequisites 1. Follow the safety guidelines listed in the Safety instructions. 2. Follow the procedure listed in the Before working inside your system. 3. Remove the air shroud. Steps 1. Loosen the captive screws on the system. 2. Press the blue release tab or blue button on the riser and holding the edges lift the expansion card riser from the riser connector on the system board. 3. Disconnect the VGA port cable from the liquid cooling (LC) rear I/O board. Figure 127. Disconnecting the VGA port cable 4. Open the latch on the expansion card riser and slide the VGA port out of the expansion card riser. 124 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
Optional VGA port for liquid cooling module
Removing the VGA port
The procedure to remove VGA port from Riser 2 is same.
Prerequisites
1.
Follow the safety guidelines listed in the
Safety instructions
.
2.
Follow the procedure listed in the
Before working inside your system
.
3.
Remove the air shroud
.
Steps
1.
Loosen the captive screws on the system.
2.
Press the blue release tab or blue button on the riser and holding the edges lift the expansion card riser from the riser
connector on the system board.
3.
Disconnect the VGA port cable from the liquid cooling (LC) rear I/O board.
Figure 127. Disconnecting the VGA port cable
4.
Open the latch on the expansion card riser and slide the VGA port out of the expansion card riser.
124
Installing and removing system components