HP 6125XLG R2306-HP 6125XLG Blade Switch Network Management and Monitoring Con - Page 105

sFlow configuration example, Network requirements, Configuration procedure

Get HP 6125XLG PDF manuals and user guides View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 105 highlights

sFlow configuration example Network requirements As shown in Figure 32, configure flow sampling in random mode and counter sampling on Ten-GigabitEthernet 1/1/5 of the device to monitor traffic on the port. Configure the device to send sampled information in sFlow packets through Ten-GigabitEthernet 1/1/7 to the sFlow collector. Figure 32 Network diagram Configuration procedure 1. Configure the IP addresses and subnet masks for interfaces, as shown in Figure 32. (Details not shown.) 2. Configure the sFlow agent and configure information about the sFlow collector: # Configure the IP address for the sFlow agent. system-view [Sysname] sflow agent ip 3.3.3.1 # Configure information about the sFlow collector: specify the sFlow collector ID as 1, IP address as 3.3.3.2, port number as 6343 (default), and description as netserver. [Sysname] sflow collector 1 ip 3.3.3.2 description netserver 3. Configure counter sampling: # Enable counter sampling and set the counter sampling interval to 120 seconds on Ten-GigabitEthernet 1/1/5. [Sysname] interface ten-gigabitethernet 1/1/5 [Sysname-Ten-GigabitEthernet1/1/5] sflow counter interval 120 # Specify sFlow collector 1 for counter sampling. [Sysname-Ten-GigabitEthernet1/1/5] sflow counter collector 1 4. Configure flow sampling: # Enable flow sampling and set the flow sampling mode to random and sampling interval to 4000. [Sysname-Ten-GigabitEthernet1/1/5] sflow sampling-mode random [Sysname-Ten-GigabitEthernet1/1/5] sflow sampling-rate 4000 # Specify sFlow collector 1 for flow sampling. [Sysname-Ten-GigabitEthernet1/1/5] sflow flow collector 1 99

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
99
sFlow configuration example
Network requirements
As shown in
Figure 32
, configure flow sampling in random mode and counter sampling on
Ten-GigabitEthernet 1/1/5 of the device to monitor traffic on the port. Configure the device to send
sampled information in sFlow packets through Ten-GigabitEthernet 1/1/7 to the sFlow collector.
Figure 32
Network diagram
Configuration procedure
1.
Configure the IP addresses and subnet masks for interfaces, as shown in
Figure 32
. (Details not
shown.)
2.
Configure the sFlow agent and configure information about the sFlow collector:
# Configure the IP address for the sFlow agent.
<Sysname> system-view
[Sysname] sflow agent ip 3.3.3.1
# Configure information about the sFlow collector: specify the sFlow collector ID as 1, IP address
as 3.3.3.2, port number as 6343 (default), and description as
netserver
.
[Sysname] sflow collector 1 ip 3.3.3.2 description netserver
3.
Configure counter sampling:
# Enable counter sampling and set the counter sampling interval to 120 seconds on
Ten-GigabitEthernet 1/1/5.
[Sysname] interface ten-gigabitethernet 1/1/5
[Sysname-Ten-GigabitEthernet1/1/5] sflow counter interval 120
# Specify sFlow collector 1 for counter sampling.
[Sysname-Ten-GigabitEthernet1/1/5] sflow counter collector 1
4.
Configure flow sampling:
# Enable flow sampling and set the flow sampling mode to random and sampling interval to
4000.
[Sysname-Ten-GigabitEthernet1/1/5] sflow sampling-mode random
[Sysname-Ten-GigabitEthernet1/1/5] sflow sampling-rate 4000
# Specify sFlow collector 1 for flow sampling.
[Sysname-Ten-GigabitEthernet1/1/5] sflow flow collector 1