HP 6125XLG R2306-HP 6125XLG Blade Switch Network Management and Monitoring Con - Page 124
Con VLAN 2 as the remote probe VLAN of the mirroring group 1, and con
View all HP 6125XLG manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 124 highlights
# Configure VLAN 2 as the remote probe VLAN of the mirroring group and Ten-GigabitEthernet 1/1/6 as the monitor port of the mirroring group, disable the spanning tree feature on Ten-GigabitEthernet 1/1/6, and assign the port to VLAN 2 as an access port. [DeviceC] mirroring-group 2 remote-probe vlan 2 [DeviceC] interface ten-gigabitethernet 1/1/6 [DeviceC-Ten-GigabitEthernet1/1/6] mirroring-group 2 monitor-port [DeviceC-Ten-GigabitEthernet1/1/6] undo stp enable 2. Configure Device B (the intermediate device): # Create VLAN 2, which is to be configured as the remote probe VLAN. system-view [DeviceB] vlan 2 # Disable MAC address learning for VLAN 2. [DeviceB-vlan2] undo mac-address mac-learning enable [DeviceB-vlan2] quit # Configure Ten-GigabitEthernet 1/1/5 as a trunk port to permit the packets of VLAN 2 to pass through. [DeviceB] interface ten-gigabitethernet 1/1/5 [DeviceB-Ten-GigabitEthernet1/1/5] port link-type trunk [DeviceB-Ten-GigabitEthernet1/1/5] port trunk permit vlan 2 [DeviceB-Ten-GigabitEthernet1/1/5] quit # Configure Ten-GigabitEthernet 1/1/6 as a trunk port to permit the packets of VLAN 2 to pass through. [DeviceB] interface ten-gigabitethernet 1/1/6 [DeviceB-Ten-GigabitEthernet1/1/6] port link-type trunk [DeviceB-Ten-GigabitEthernet1/1/6] port trunk permit vlan 2 [DeviceC-Ten-GigabitEthernet1/1/6] quit 3. Configure Device A (the source device): # Create a remote source group. system-view [DeviceA] mirroring-group 1 remote-source # Create VLAN 2, which is to be configured as the remote probe VLAN. [DeviceA] vlan 2 # Disable MAC address learning for VLAN 2. [DeviceA-vlan2] undo mac-address mac-learning enable [DeviceA-vlan2] quit # Configure VLAN 2 as the remote probe VLAN of the mirroring group 1, and configure Ten-GigabitEthernet 1/1/5 as a source port and Ten-GigabitEthernet 1/1/6 as the egress port in the mirroring group. [DeviceA] mirroring-group 1 remote-probe vlan 2 [DeviceA] mirroring-group 1 mirroring-port ten-gigabitethernet 1/1/5 both [DeviceA] mirroring-group 1 monitor-egress ten-gigabitethernet 1/1/6 # Configure port Ten-GigabitEthernet 1/1/6 as a trunk port to permit the packets of VLAN 2 to pass through, and disable the spanning tree feature on the port. [DeviceA] interface ten-gigabitethernet 1/1/6 [DeviceA-Ten-GigabitEthernet1/1/6] port link-type trunk [DeviceA-Ten-GigabitEthernet1/1/6] port trunk permit vlan 2 118