Oki MB471 Quick Start Guide - Page 13

Installing Your Machine, Installation Requirements, Installation Space

Page 13 highlights

Installing Your Machine ●●Installing Your Machine 1 This section explains how to unpack and install the machine. Machine Setup Installation Requirements This section explains the required environment and space for machine installation. Installation Environment Your machine must be installed in the following environment: Temperature: Humidity: Maximum wet bulb temperature: 10°C~32°C 20%~80% RH (relative humidity) 25°C Note ●● Be careful of condensation. It may cause a malfunction. ●● If installing your machine where the relative humidity of the surrounding air is less than 30%, use a humidifier or antistatic mat. Installation Space Install your machine on a flat surface that is wide enough to accommodate the machine. Allow for enough room around your machine according to the images below. ●● Top view (193cm) 20cm * 50cm 20cm 100cm * M B461+LP/MB491+LP/MPS4700mb: 89cm Other: 83cm ●● Side view WARNING 50cm ●● Do not place in hot locations or near fire. ●● Do not install in locations where chemical reactions take place (laboratory etc.). ●● Do not place in locations near flammable solutions (96cm) such as alcohol and thinner. ●● Do not place in locations within reach of small children. ●● Do not install in unstable locations (wobbly stand, angled place, etc.). ●● Do not install in locations with high humidity or dust and where exposed to direct sunlight. ●● Do not install in an environment exposed to briny air and corrosive gas. ●● Do not install in locationss with much vibration. ●● Do not install in locations where the ventilation holes of the machine are blocked. CAUTION ●● Do not place directly on a rug or carpet with long strands. ●● Do not install in a closed room with poor ventilation or circulation. ●● If you use the machine in a small room for a long time, please make sure that you ventilate the room. ●● Install away from strong magnetic fields and sources of noise. ●● Install away from monitors or TVs. ●● When moving the machine, hold it on both sides, and move it by slightly tilting the back down. - 13 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128

- 13 -
Installing Your Machine
1
Machine Setup
Installing Your Machine
This section explains how to unpack and install the machine.
Installation Requirements
This section explains the required environment
and space for machine installation.
Installation Environment
Your machine must be installed in the following
environment:
Temperature:
10°C~32°C
Humidity:
20%~80% RH (relative
humidity)
Maximum wet bulb
temperature:
25°C
Note
Be careful of condensation. It may cause a malfunction.
If installing your machine where the relative humidity of
the surrounding air is less than 30%, use a humidifier or
antistatic mat.
WARNING
Do not place in hot locations or near fire.
Do not install in locations where chemical
reactions take place (laboratory etc.).
Do not place in locations near flammable solutions
such as alcohol and thinner.
Do not place in locations within reach of small
children.
Do not install in unstable locations (wobbly stand,
angled place, etc.).
Do not install in locations with high humidity or
dust and where exposed to direct sunlight.
Do not install in an environment exposed to briny
air and corrosive gas.
Do not install in locationss with much vibration.
Do not install in locations where the ventilation
holes of the machine are blocked.
CAUTION
Do not place directly on a rug or carpet with long
strands.
Do not install in a closed room with poor
ventilation or circulation.
If you use the machine in a small room for a long
time, please make sure that you ventilate the
room.
Install away from strong magnetic fields and
sources of noise.
Install away from monitors or TVs.
When moving the machine, hold it on both sides,
and move it by slightly tilting the back down.
Installation Space
Install your machine on a flat surface that is
wide enough to accommodate the machine.
Allow for enough room around your machine
according to the images below.
Top view
20cm
(193cm)
20cm
50cm
100cm
*
* MB461+LP/MB491+LP/MPS4700mb: 89cm
Other: 83cm
Side view
50cm
(96cm)