Oki MB471 Quick Start Guide - Page 52

Connecting using wired LAN, the network interface connection on

Get Oki MB471 PDF manuals and user guides View all Oki MB471 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Scanning Scanning to E-mail Note ●● When setting an IP address manually, ask the network administrator or your Internet service provider which IP address to use. If the IP address is set incorrectly, the network may go down or Internet access may be disabled. ●● Conform the IP version of the machine to that of your computer. ●● Set [TCP/IP] setting to [Enable] on your machine. (By factory default, it is set to [Enable].) Memo ●● If configuring a small network consisting of only your machine and a computer, set IP addresses as shown below (according to RFC1918). For the computer IP address : 192.168.0.1~254 4 Subnet mask : 255.255.255.0 Default gateway : not used DNS server : not used For the machine IP Address Set : Manual IPv4 Address : 192.168.0.1~254 (select a different value from the computer) Subnet Mask : 255.255.255.0 Gateway Address : 0.0.0.0 Network Scale : Small ●● To set [Network Scale], press the key and then select [Admin Setup] > [Network Menu] > [Network Setup] > [Network Scale]. 3 Plug one end of the Ethernet cable into the network interface connection on the back of the machine. 4 Plug the other end of the Ethernet cable into the hub. „„Connecting using wired LAN 1 Prepare an Ethernet cable and a hub. Prepare an Ethernet cable (category 5, twisted pair, straight) and a hub separately. 5 Hold down the power switch for approximately one second to turn on the power. 2 Hold down the power switch for approximately one second to turn off the power. - 52 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
- 52 -
Scanning to E-mail
4
Scanning
Note
●
When setting an IP address manually, ask the network
administrator or your Internet service provider which IP
address to use. If the IP address is set incorrectly, the
network may go down or Internet access may be disabled.
●
Conform the IP version of the machine to that of your
computer.
●
Set [
TCP/IP
] setting to [
Enable
] on your machine. (By
factory default, it is set to [
Enable
].)
Memo
●
If configuring a small network consisting of only your
machine and a computer, set IP addresses as shown
below (according to RFC1918).
For the computer
IP address :
192.168.0.1~254
Subnet mask :
255.255.255.0
Default gateway :
not used
DNS server :
not used
For the machine
IP Address Set :
Manual
IPv4 Address :
192.168.0.1~254
(select a different value
from the computer)
Subnet Mask :
255.255.255.0
Gateway Address : 0.0.0.0
Network Scale :
Small
●
To set [
Network Scale
], press the <
SETTING
> key
and then select [
Admin Setup
] > [
Network Menu
] >
[
Network Setup
] > [
Network Scale
].
±
Connecting using wired LAN
1
Prepare an Ethernet cable and a hub.
Prepare an Ethernet cable (category 5, twisted
pair, straight) and a hub separately.
2
Hold down the power switch for
approximately one second to turn off the
power.
3
Plug one end of the Ethernet cable into
the network interface connection on the
back of the machine.
4
Plug the other end of the Ethernet cable
into the hub.
5
Hold down the power switch for
approximately one second to turn on the
power.