Oki MB471 Quick Start Guide - Page 85

For WSD Scan Connection, Step 1 Configuring the Network

Get Oki MB471 PDF manuals and user guides View all Oki MB471 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

13 When the instruction to connect the machine to the computer and turn on the machine is displayed, plug the other end of the USB cable into the computer's USB interface connector and hold down the power switch for approximately one second to turn on the power. Note ●● Do not plug the USB cable into the network interface connection. Doing so may damage your machine. 14 Click the [Exit] button. 15 Remove "Software DVD-ROM" from the computer. The installation is complete. Scanning to Local PC „„For WSD Scan Connection To configure the Scan to Local PC via the WSD Scan connection, follow the 2 steps below: ●● "Step 1 Configuring the Network Settings of Your Machine" P.85 ●● "Step 2 Installing Your Machine to the Computer" P.89 Note ●● You need to configure the network setting of the computer before this procedure. Memo ●● You can skip step 1 if the IP address is already set on your machine. 4 ‰‰Step 1 Configuring the Network Settings of Your Machine Connect your machine to a network with an Ethernet cable or Wireless LAN connection (MB451w, MB471w only), and then configure the machine's IP address and other network information from the operator panel. You can set the IP address either manually or automatically. If there is no DHCP server or BOOTP server on the network, you need to manually configure the IP address on the computer or machine. If your network administrator or Internet service provider specifies a unique IP address for the computer and your machine, set the IP addresses manually. Note ●● When setting an IP address manually, ask the network administrator or your Internet service provider which IP address to use. If the IP address is set wrong, the network may go down or Internet access may be disabled. ●● To configure the Scan to Local PC function via the WSD Scan connection, follow these instructions. --Conform the IP version of the machine to that of your computer. --Set [TCP/IP] setting to [Enable] on your machine. (By factory default, it is set to [Enable].) --Set [WSD Scan] setting to [Enable] on your machine. (By factory default, it is [Enable]. If it has been disabled, enable it by referring to the User's Manual (Advanced) > "3. Scanning" > "Useful Functions for Scanning to Local and Remote PCs" > "Enabling the WSD Scan".) Scanning - 85 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
- 85 -
Scanning to Local PC
4
Scanning
13
When the instruction to connect the
machine to the computer and turn on
the machine is displayed, plug the other
end of the USB cable into the computer’s
USB interface connector and hold down
the power switch for approximately one
second to turn on the power.
Note
●
Do not plug the USB cable into the network interface
connection. Doing so may damage your machine.
14
Click the [
Exit
] button.
15
Remove “Software DVD-ROM” from the
computer.
The installation is complete.
±
For WSD Scan Connection
To configure the Scan to Local PC via the WSD
Scan connection, follow the 2 steps below:
●
“Step 1 Configuring the Network Settings of
Your Machine” P.85
●
“Step 2 Installing Your Machine to the
Computer” P.89
Note
●
You need to configure the network setting of the computer
before this procedure.
Memo
●
You can skip step 1 if the IP address is already set on your
machine.
²
Step 1 Configuring the Network
Settings of Your Machine
Connect your machine to a network with an
Ethernet cable or Wireless LAN connection
(MB451w, MB471w only), and then configure
the machine’s IP address and other network
information from the operator panel. You can set
the IP address either manually or automatically.
If there is no DHCP server or BOOTP server on
the network, you need to manually configure the
IP address on the computer or machine.
If your network administrator or Internet
service provider specifies a unique IP address
for the computer and your machine, set the IP
addresses manually.
Note
●
When setting an IP address manually, ask the network
administrator or your Internet service provider which
IP address to use. If the IP address is set wrong, the
network may go down or Internet access may be disabled.
●
To configure the Scan to Local PC function via the WSD
Scan connection, follow these instructions.
- Conform the IP version of the machine to that of your
computer.
- Set [
TCP/IP
] setting to [
Enable
] on your machine.
(By factory default, it is set to [
Enable
].)
- Set [
WSD Scan
] setting to [
Enable
] on your
machine. (By factory default, it is [
Enable
]. If it
has been disabled, enable it by referring to the
User’s Manual (Advanced) > “3. Scanning” > “Useful
Functions for Scanning to Local and Remote PCs” >
“Enabling the WSD Scan”.)