Dell PowerEdge XL 5133-4 MXL 10/40GbE Switch IO Module FTOS Command Reference - Page 39
Completed Boot Process Contd.
View all Dell PowerEdge XL 5133-4 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 39 highlights
Figure 4-4. Completed Boot Process (Contd.) # # # u-boot: for Navasota board # # # Initialized CPLD on CS3 Detected [XLP308 (Lite) Rev A0] CPLD reg 06 val 0xf7 This is a NAVASOTA ... Initializing I2C0: speed = 30 KHz, prescaler = 0x0377 -- done. Initializing I2C1: speed = 100 KHz, prescaler = 0x0109 -- done. Initialized eMMC Host Controller Detected SD Card Now running in RAM - U-Boot [N64 ABI, Big-Endian] at: ffffffff8c100000 Flash: 256 MB PCIE (B0:D01:F0) : Link up. In: serial Out: serial Err: serial Net: nae-0: PHY is Broadcom BCM54616S --More-- RELEASE IMAGE HEADER DATA More-- SOFTWARE IMAGE HEADER DATA More-Starting Dell Force10 application 00:00:15: %STKUNIT0-M:CP %RAM-6-ELECTION_ROLE: Stack unit 0 is transitioning to Management unit. 00:00:16: %STKUNIT0-M:CP %CHMGR-5-STACKUNITDETECTED: Stack unit 0 present 00:00:18: %STKUNIT0-M:CP %CHMGR-5-CHECKIN: Checkin from Stack unit 0 (type I/O-Aggregator, 56 ports) 00:00:18: %I/O-Aggregator:0 %LCMGR-5-IOM_STATE: Switch status of stack-unit 0 is set to Good 00:00:18: %STKUNIT0-M:CP %IFMGR-5-ASTATE_UP: Changed uplink state group Admin state to up: Group 1 00:00:18: %STKUNIT0-M:CP %CHMGR-5-STACKUNITUP: Stack unit 0 is up 00:00:20: %STKUNIT0-M:CP %CHMGR-5-SYSTEM_READY: System ready 00:00:20: %STKUNIT0-M:CP %IFMGR-5-OSTATE_UP: Changed interface state to up: Ma 0/0 00:00:22: %I/O-Aggregator:0 %POLLMGR-2-MODULE_POWER_STATE: Module 0 in unit 0 changed to POWER GOOD state 00:00:23: %STKUNIT0-M:CP %CHMGR-0-TEMP_STATUS_CHANGE: Unit 0 temperature state changed to 1. 00:00:24: %STKUNIT0-M:CP %RAM-5-STACK_STATE: Stack unit 0 is in Active State. 00:00:25: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_QSFP: Optics QSFP inserted in slot 0 port 33 00:00:25: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_QSFP: Optics QSFP inserted in slot 0 port 34 00:00:25: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_QSFP: Optics QSFP inserted in slot 0 port 35 00:00:26: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_QSFP: Optics QSFP inserted in slot 0 port 36 00:00:26: %STKUNIT0-M:CP %CHMGR-5-MODULE_INSERTED: SFP+ module has been inserted in stack-unit 0 optional slot 0 00:00:27: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_PLUS: Optics SFP+ inserted in slot 0 port 41 00:00:28: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_PLUS: Optics SFP+ inserted in slot 0 port 42 00:00:28: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_PLUS: Optics SFP+ inserted in slot 0 port 43 00:00:28: %I/O-Aggregator:0 %IFAGT-5-INSERT_OPTICS_PLUS: Optics SFP+ inserted in slot 0 port 44 Getting Started | 25