Epson Equity LT User Manual - Page 75

Copying with one 5 1/4-inch diskette drive, Press any key when ready ..

Get Epson Equity LT PDF manuals and user guides View all Epson Equity LT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

6. When the copy is completed, you see this message: Copy another diskette (Y/N)? Your diskette has now been copied and you can either make another copy or leave the DISKCOPY command. Press Y to perform another copy or N to end the DISKCOPY command. Copying with one 5 f -inch diskette drive Follow the steps below to make a copy of a 360KB diskette in an external 5 + -inch diskette drive. These instructions assume the external drive is assigned as drive B. If you turned off DIP switch 2 on the back panel to make the external drive A, substitute A for B in the instructions. 1. First be sure your original diskette is write-protected. (There should be a write-protect tab over the write-protect notch.) 2. Insert the working copy of your MS-DOS system diskette in drive A (or type C: to log on to drive C if you have a hard disk). 3. At the A> or C> prompt, type: DISKCOPY B: B: and press Enter. MS-DOS displays these messages: Insert SOURCE diskette in drive B: Press any key when ready . . . 4. Insert the diskette you want to copy from in the external diskette drive (B) and press Enter. DISKCOPY copies the contents of the diskette to the computer's memory. Then the screen displays these messages: Insert TARGET diskette in drive B: Press any key when ready . . . Using MS-DOS With the Equity LT 4-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
6.
When the copy is completed, you see this message:
Copy another diskette (Y/N)?
Your diskette has now been copied and you can either
make another copy or leave the DISKCOPY command.
Press Y to perform another copy or
N
to end the
DISKCOPY command.
Copying with one 5
f
-inch diskette drive
Follow the steps below to make a copy of a 360KB diskette
in an external 5
+
-inch diskette drive. These instructions
assume the external drive is assigned as drive B. If you turned
off DIP switch 2 on the back panel to make the external drive
A, substitute A for B in the instructions.
1.
First be sure your original diskette is write-protected.
(There should be a write-protect tab over the write-protect
notch.)
2.
Insert the working copy of your MS-DOS system diskette
in drive A (or type C: to log on to drive C if you have a
hard disk).
3. At the A> or C> prompt, type:
DISKCOPY B: B:
and press
Enter.
MS-DOS displays these messages:
Insert SOURCE diskette in drive B:
Press any key when ready . . .
4.
Insert the diskette you want to copy from in the external
diskette drive (B) and press
Enter.
DISKCOPY copies the contents of the diskette to the
computer’s memory. Then the screen displays these
messages:
Insert TARGET diskette in drive B:
Press any key when ready . . .
Using MS-DOS With the Equity LT
4-11