HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Command - Page 131

vrrp ipv6 vrid priority

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 131 highlights

If you set the router in the VRRP group to operate in non-preemptive mode, the delay period automatically changes to zero seconds. To avoid frequent member state changes in a VRRP group and make the backups have enough time to collect information (such as routing information), each backup waits for a period of time (the preemption delay time) after it receives an advertisement with the priority lower than the local priority, then sends VRRP advertisements to start a new master election in the VRRP group and becomes the master. Before executing the command, create a VRRP group on an interface and configure the virtual IPv6 address of the VRRP group. Related commands: display vrrp ipv6. Examples # Enable preemption on the switch in VRRP group 80 and set the preemption delay to five seconds. system-view [Sysname] interface vlan-interface 2 [Sysname-Vlan-interface2] vrrp ipv6 vrid 10 virtual-ip fe80::2 link-local [Sysname-Vlan-interface2] vrrp ipv6 vrid 10 preempt-mode timer delay 5 vrrp ipv6 vrid priority Syntax vrrp ipv6 vrid virtual-router-id priority priority-value View undo vrrp ipv6 vrid virtual-router-id priority Interface view Default level 2: System level Parameters virtual-router-id: VRRP group number, which ranges from 1 to 255. priority-value: Priority value of the router in the specified VRRP group, which ranges from 1 to 254. A higher number indicates a higher priority. Description Use vrrp ipv6 vrid priority to configure the priority of the router in the specified VRRP group. Use undo vrrp ipv6 vrid priority to restore the default. By default, the priority of a router in a VRRP group is 100. Before executing the command, create a VRRP group on an interface and configure the virtual IPv6 address of the VRRP group. The role that a router plays in a VRRP group depends on its priority. A higher priority means that the router is more likely to become the master. Priority 0 is reserved for special use and 255 for the IP address owner. If the router is the IP address owner, its priority is always 255. Therefore, it remains as the master as long as it is functioning normally. Related commands: display vrrp ipv6. 126

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
126
If you set the router in the VRRP group to operate in non-preemptive mode, the delay period automatically
changes to zero seconds.
To avoid frequent member state changes in a VRRP group and make the backups have enough time to
collect information (such as routing information), each backup waits for a period of time (the preemption
delay time) after it receives an advertisement with the priority lower than the local priority, then sends
VRRP advertisements to start a new master election in the VRRP group and becomes the master.
Before executing the command, create a VRRP group on an interface and configure the virtual IPv6
address of the VRRP group.
Related commands:
display vrrp ipv6
.
Examples
# Enable preemption on the switch in VRRP group 80 and set the preemption delay to five seconds.
<Sysname> system-view
[Sysname] interface vlan-interface 2
[Sysname-Vlan-interface2] vrrp ipv6 vrid 10 virtual-ip fe80::2 link-local
[Sysname-Vlan-interface2] vrrp ipv6 vrid 10 preempt-mode timer delay 5
vrrp ipv6 vrid priority
Syntax
vrrp ipv6 vrid
virtual-router-id
priority
priority-value
undo vrrp ipv6 vrid
virtual-router-id
priority
View
Interface view
Default level
2: System level
Parameters
virtual-router-id
: VRRP group number, which ranges from 1 to 255.
priority-value
: Priority value of the router in the specified VRRP group, which ranges from 1 to 254. A
higher number indicates a higher priority.
Description
Use
vrrp ipv6 vrid priority
to configure the priority of the router in the specified VRRP group.
Use
undo vrrp ipv6 vrid priority
to restore the default.
By default, the priority of a router in a VRRP group is 100.
Before executing the command, create a VRRP group on an interface and configure the virtual IPv6
address of the VRRP group.
The role that a router plays in a VRRP group depends on its priority. A higher priority means that the
router is more likely to become the master. Priority 0 is reserved for special use and 255 for the IP address
owner.
If the router is the IP address owner, its priority is always 255. Therefore, it remains as the master as long
as it is functioning normally.
Related commands:
display vrrp ipv6
.