HP 6125G HP 6125G & 6125G/XG Blade Switches High Availability Command - Page 94

VRRP configuration commands, vrrp mode

Get HP 6125G PDF manuals and user guides View all HP 6125G manuals
Add to My Manuals
Save this manual to your list of manuals

Page 94 highlights

VRRP configuration commands • The term router in this document refers to both routers and Layer 3 switches. • The term interface in the VRRP feature refers to VLAN interfaces. Common VRRP configuration commands vrrp mode Syntax vrrp mode load-balance View undo vrrp mode System view Default level 2: System level Parameters load-balance: Specifies the load balancing mode. Description Use vrrp mode to configure the VRRP working mode. Use undo vrrp mode to restore the default. By default, VRRP operates in standard protocol mode. • When you configure the working mode of VRRP by using this command, both IPv4-based and IPv6-based VRRP groups operate in the specified mode. • When VRRP operates in load balancing mode, the virtual IP address cannot be the same as the IP address of any interface in the VRRP group, and the virtual IP address should be mapped to the virtual MAC address. Otherwise, VRRP cannot operate in load balancing mode. • When a VRRP group is created, you can still change the VRRP working mode. When you change the VRRP working mode, all VRRP groups on the router operate in the specified mode. Related commands: display vrrp and display vrrp ipv6. Examples # Configure VRRP to operate in load balancing mode. system-view [Sysname] vrrp mode load-balance 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
89
VRRP configuration commands
•
The term
router
in this document refers to both routers and Layer 3 switches.
•
The term
interface
in the VRRP feature refers to VLAN interfaces.
Common VRRP configuration commands
vrrp mode
Syntax
vrrp mode load-balance
undo vrrp mode
View
System view
Default level
2: System level
Parameters
load-balance
: Specifies the load balancing mode.
Description
Use
vrrp mode
to configure the VRRP working mode.
Use
undo vrrp mode
to restore the default.
By default, VRRP operates in standard protocol mode.
•
When you configure the working mode of VRRP by using this command, both IPv4-based and
IPv6-based VRRP groups operate in the specified mode.
•
When VRRP operates in load balancing mode, the virtual IP address cannot be the same as the IP
address of any interface in the VRRP group, and the virtual IP address should be mapped to the
virtual MAC address. Otherwise, VRRP cannot operate in load balancing mode.
•
When a VRRP group is created, you can still change the VRRP working mode. When you change
the VRRP working mode, all VRRP groups on the router operate in the specified mode.
Related commands:
display vrrp
and
display
vrrp ipv6
.
Examples
# Configure VRRP to operate in load balancing mode.
<Sysname> system-view
[Sysname] vrrp mode load-balance