Home » Lexmark Manuals » Laser Printers » Lexmark C524 » Manual Viewer

Lexmark C524 User's Guide - Page 107

Restoring factory default settings, Adjusting Power Saver

Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Administrative support Restoring factory default settings When first entering the printer menus from the operator panel, notice an asterisk (*) next to a value in the menus. This asterisk indicates the factory default setting. These settings are the original printer settings. (Factory defaults may vary for different countries and regions.) When a new setting is selected from the operator panel, the Saved message appears. When the Saved message disappears, an asterisk appears next to the setting to identify it as the current user default setting. These settings are active until new ones are stored or the factory defaults are restored. To restore the original printer factory default settings: 1 Make sure the printer is on and the Ready message appears. 2 Press to enter the menus. 3 Press until Settings appears, and then press . 4 Press until Setup Menu appears, and then press . 5 Press until Factory Defaults appears, and then press . 6 Press until Restore Now appears, and then press . The message Restoring Factory Defaults appears, followed by the Ready message. When Restore is selected: • No other button actions are available on the operator panel while Restoring Factory Defaults appears. • All downloaded resources (fonts, macros, and symbol sets) in printer memory (RAM) are deleted. (Resources residing in flash memory or on the optional hard disk are unaffected.) • All menu settings are returned to the factory default values, except: - The operator panel Display Language setting in the Setup Menu. - All settings in the Parallel Menu, Serial Menu, Network Menu, and USB Menu. Adjusting Power Saver To adjust the Power Saver setting in the Setup Menu: 1 Make sure the printer is on and the Ready message appears. 2 Press to enter the menus. 3 Press until Settings appears, and then press . 4 Press until Setup Menu appears, and then press . 5 Press until Power Saver. appears, and then press . 6 Press or press . to decrease or increase the number in the scale for the desired number of minutes, and then Minute settings available range from 1-240. The menu value Disabled is also available if Energy Conserve is set to Disabled. The Submitting Selection message appears. Note: The Power Saver setting may also be adjusted by issuing a Printer Job Language (PJL) command. For more information, see the Technical Reference available on our Lexmark Web site at www.lexmark.com. Restoring factory default settings 107

Section	Page
Contents	3
Overview	8
Basic models	8
Configured model	9
Illustrations in this publication	9
Installing drivers for local printing	10
Windows	10
Using Windows Server 2003, Windows2000, WindowsXP, Windows98SE, WindowsMe, or WindowsNT	10
Using Windows 95 and Windows 98 (first edition)	11
Serial printing	11
Macintosh	13
Creating a queue in Print Center / Printer Setup Utility (MacOSX)	14
UNIX/Linux	15
Installing drivers for network printing	16
Printing a network setup page	16
Assigning a printer IP address	16
Verifying the IP settings	17
Windows	17
Supported printer drivers	17
Supported network printer ports	17
Direct printing using Windows98SE, Me, WindowsNT4.0, Windows2000, WindowsXP, or WindowsSer...	18
Shared printing using WindowsNT 4.0, Windows2000, WindowsXP, or WindowsServer2003	19
Configuring Drag‘N’Print	21
Macintosh	21
Mac OS X	21
MacOS9.x	22
UNIX/Linux	23
NetWare	23
Printing	24
Tips for successful printing	24
Tips on storing media	24
Avoiding jams	24
Sending a job to print	24
Sending a job from a typical Windows application	24
Sending a job from a typical Macintosh application	25
Printing or deleting a confidential job	25
Entering a personal identification number (PIN)	26
Canceling a print job	26
Canceling from the printer operator panel	27
Canceling a job from a computer running Windows	27
Canceling a job from a Macintosh computer running Mac OS 9.x	27
Canceling a job from a Macintosh computer running Mac OS X	27
Printing the menu settings page	28
Printing a directory list	28
Printing a font sample list	28
Printing the Print Quality Test Pages	29
Printing only black text and graphics	29
Configuring the printer for black-only printing	29
Removing the color supplies	30
Configuring the printer for color printing and replacing the supplies	33
Media specifications	35
Media guidelines	35
Paper	35
Transparencies	37
Envelopes	38
Labels	39
Card stock	39
Storing media	40
Identifying media sources and specifications	40
Tray linking	45
Using the duplex function (two-sided printing)	45
Duplex printing on letterhead	45
Using Duplex Bind	45
Loading media	47
Loading the standard tray	47
Loading the optional 500-sheet tray	50
Identifying the multipurpose feeder or the manual feed slot	50
Using and loading the multipurpose feeder	50
Loading the multipurpose feeder	51
Using and loading the manual feed slot	57
Using the standard bin	59
Attaching the standard bin	59
Using the media stop	60
Setting the Paper Type and Paper Size	62
Clearing jams	63
Avoiding jams hints	63
Identifying the media path	64
Accessing jam areas	65
Clearing a jam in the standard tray (Tray 1)	67
Clearing a jam in the optional 500-sheet tray (Tray 2)	68
Clearing jams behind the inner door	69
Clearing jams under the fuser or fuser cover	71
Clearing jams between the fuser and the standard bin	73
Clearing a jam in the standard bin	73
Clearing duplex path jams	74
Clearing jams from the multipurpose feeder	77
Clearing jams from the manual feed slot	77
Maintaining the printer	78
Determining the status of supplies	78
Conserving supplies	78
Ordering supplies and maintenance items	79
Ordering toner cartridges	79
Ordering a photoconductor unit	80
Ordering a fuser	80
Ordering a transfer belt	80
Ordering a waste toner box	80
Maintaining the printer for long-term storage	80
Storing supplies	81
Storing media	81
Storing the toner cartridges and photoconductor units	81
Replacing the toner cartridges	81
Recycling Lexmark products	83
Replacing the photoconductor units	83
Replacing the fuser	83
Replacing the waste toner box	83
Replacing the transfer belt	83
Cleaning the printhead lenses	84
Aligning the toner cartridges for color registration	85
Removing the fuser for long-term storage	86
Replacing the fuser after long-term storage	88
Troubleshooting	90
Solving basic printer problems	90
Solving display problems	91
Solving printing problems	91
Solving print quality problems	93
Solving option problems	98
Solving media feed problems	99
Solving network printing problems	101
Solving other problems	101
Solving color quality problems	101
Frequently asked questions (FAQ) about color printing	102
What are Detailed Color Samples and how do I access them?	104
Online technical support	105
Calling for service	105
Administrative support	106
Disabling operator panel menus	106
Enabling menus	106
Restoring factory default settings	107
Adjusting Power Saver	107
Disabling Power Saver	108
Encrypting the disk	108
Configuring printer alerts	109
Adjusting operator panel contrast	109
Memory requirements	110
Using the Print and Hold function	110
Selecting a user name	110
Printing and deleting held jobs	110
Accessing held jobs from the operator panel	111
Repeat Print	111
Reserve Print	111
Verify Print	111
Confidential jobs	112
Understanding the operator panel	113
Indicator light	113
Buttons	114
Using the security lock feature	115
Setting security using the Embedded Web Server (EWS)	115
Setting the system password	115
Using the secure Embedded Web Server	115
Supporting SNMPv3 (Simple Network Management Protocol version 3)	116
Supporting IPSec (Internet Protocol Security)	116
Using Secure mode	116
Using 802.1x Authenticating	117
Locking the operator panel menus	117
Printing Lockout	118
Confidential Print Setup	118
Installing and removing options	119
Installing the 500-sheet drawer	119
Removing the 500-sheet drawer	120
Accessing the system board	120
Replacing the system board metal plate	123
Installing an optional memory card	124
Removing a memory card	126
Installing an optional flash memory or firmware card	127
Removing an optional flash memory or firmware card	128
Installing an optional hard disk	129
Removing an optional hard disk	130
Installing an optional INA card	131
Removing an optional INA card	132
Attaching cables	133
Notices	134
Licensing notice	135
Conventions	135
Static sensitivity notice	136
Electronic emission notices	136
Federal Communications Commission (FCC) compliance information statement	136
Industry Canada compliance statement	137
Avis de conformité aux normes de l’industrie du Canada	137
European Community (EC) directives conformity	137
The United Kingdom Telecommunications Act 1984	137
Japanese VCCI notice	137
Korean MIC statement	137
Noise emission levels	138
Energy consumption	138
Power regulation notice	138
Total energy usage	138
Power Saver	139
ENERGY STAR	139
Waste from Electrical and Electronic Equipment (WEEE) directive	139
Laser notice	140
Statement of Limited Warranty for Lexmark C520, C522, and C524	140

Match case Limit results 1 per page

Restoring factory default settings

107

Administrative support

Restoring factory default settings

When first entering the printer menus from the operator panel, notice an asterisk (*) next to a value in the menus. This

asterisk indicates the

factory default setting

. These settings are the original printer settings. (Factory defaults may vary for

different countries and regions.)

When a new setting is selected from the operator panel, the

Saved

message appears. When the

Saved

message

disappears, an asterisk appears next to the setting to identify it as the current

user default setting

. These settings are active

until new ones are stored or the factory defaults are restored.

To restore the original printer factory default settings:

Make sure the printer is on and the

Ready

message appears.

Press

to enter the menus.

Press

until

Settings

appears, and then press

Press

until

Setup Menu

appears, and then press

Press

until

Factory Defaults

appears, and then press

Press

until

Restore Now

appears, and then press

The message

Restoring Factory Defaults

appears, followed by the

Ready

message.

When Restore is selected:

•

No other button actions are available on the operator panel while

Restoring Factory Defaults

appears.

•

All downloaded resources (fonts, macros, and symbol sets) in printer memory (RAM) are deleted. (Resources

residing in flash memory or on the optional hard disk are unaffected.)

•

All menu settings are returned to the factory default values, except:

–

The operator panel Display Language setting in the

Setup Menu

–

All settings in the

Parallel Menu

Serial Menu

Network Menu

, and

USB Menu

Adjusting Power Saver

To adjust the

Power Saver

setting in the

Setup Menu

Make sure the printer is on and the

Ready

message appears.

Press

to enter the menus.

Press

until

Settings

appears, and then press

Press

until

Setup Menu

appears, and then press

Press

until

Power Saver

. appears, and then press

Press

to decrease or increase the number in the scale for the desired number of minutes, and then

press

Minute settings available range from 1

–

240. The menu value

Disabled

is also available if

Energy Conserve

set to

Disabled

The

Submitting Selection

message appears.

Note:

The Power Saver setting may also be adjusted by issuing a Printer Job Language (PJL) command.

For more information, see the

Technical Reference

available on our Lexmark Web site at