Sony PMW200 User Manual (PMW-100 Memory Camcorder Operation Manual for Firmwar - Page 24

Using the IR Remote Commander, Before use, Replacing the battery in the IR Remote, Commander

Get Sony PMW200 PDF manuals and user guides View all Sony PMW200 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 24 highlights

Preparations Using the IR Remote Commander Before use Before you use the supplied IR Remote Commander for the first time, pull out the insulation sheet from the battery holder. Replacing the battery in the IR Remote Commander Use a commercially available CR2025 lithium battery. Do not use any battery other than a CR2025. 1 Hold down the lock lever 1, pull out the battery holder 2, and remove the battery. Insulation sheet A CR2025 lithium battery is set in the holder at the factory. To use the IR Remote Commander For controlling the camcorder from the IR Remote Commander, activate the remote control function of the camcorder after turning the power on. Activating/deactivating the remote control function can be achieved using the Setup menu or an assignable button. To activate using the menu Press the MENU button to set the camcorder to Menu mode, select (the OTHERS menu (page 96)) and set "IR Remote" to "On." To activate using an assignable button Assigning "IR Remote" to one of the assignable buttons (page 49) permits you to activate/ deactivate the remote control function by pressing the button. Note To avoid malfunctions, the remote control function is automatically deactivated when the camcorder is turned off. Activate the function each time when required after you turn the camcorder on. 2 1 2 Place a new battery in the battery holder with the + symbol facing upward 1, then push the battery holder into the IR Remote Commander until it clicks 2. With the + symbol upward 1 2 WARNING • Battery may explode if mistreated. Do not recharge, disassemble, or dispose of in fire. • Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. When you dispose of the battery, you must obey the law in the relative area or country. 24 Using the IR Remote Commander

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
Using the IR Remote Commander
24
Preparations
Before use
Before you use the supplied IR Remote
Commander for the first time, pull out the
insulation sheet from the battery holder.
A CR2025 lithium battery is set in the holder at
the factory.
To use the IR Remote Commander
For controlling the camcorder from the IR
Remote Commander, activate the remote control
function of the camcorder after turning the power
on.
Activating/deactivating the remote control
function can be achieved using the Setup menu or
an assignable button.
To activate using the menu
Press the MENU button to set the camcorder to
Menu mode, select
(the OTHERS menu
(page 96)
) and set “IR Remote” to “On.”
To activate using an assignable button
Assigning “IR Remote” to one of the assignable
buttons
(page 49)
permits you to activate/
deactivate the remote control function by
pressing the button.
Note
To avoid malfunctions, the remote control function is
automatically deactivated when the camcorder is turned
off. Activate the function each time when required after
you turn the camcorder on.
Replacing the battery in the IR Remote
Commander
Use a commercially available CR2025 lithium
battery. Do not use any battery other than a
CR2025.
1
Hold down the lock lever
1
, pull out
the battery holder
2
, and remove the
battery.
2
Place a new battery in the battery
holder with the + symbol facing upward
1
, then push the battery holder into the
IR Remote Commander until it clicks
2
.
•
Battery may explode if mistreated.
Do not recharge, disassemble, or dispose of in
fire.
•
Batteries shall not be exposed to excessive heat
such as sunshine, fire or the like.
Danger of explosion if battery is incorrectly
replaced. Replace only with the same or
equivalent type recommended by the
manufacturer.
When you dispose of the battery, you must obey
the law in the relative area or country.
Using the IR Remote
Commander
Insulation sheet
WARNING
CAUTION
1
2
1
2
With the + symbol upward