Dell PowerConnect W-IAP92 Dell Instant 6.1.2.3-2.0.0.0 User Guide - Page 57

unrestricted, network based, any permit, instant

Get Dell PowerConnect W-IAP92 PDF manuals and user guides View all Dell PowerConnect W-IAP92 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Figure 36 Login Window 7. Create a new SSID and wpa-2 personal keys with unrestricted or network based access rules. Select any permit for basic connectivity. 8. Connect a client to the new SSID and disconnect from the instant SSID. 9. All the IAPs will show up on the Virtual Controller as shown in the figure below. Disconnect the IAPs that you want to deploy as Mesh Points from the switch and place the IAPs at the desired location. The wired IAPs are Mesh Portals. Figure 37 Mesh Portal NOTE: The IAPs in US, JP, or IL regulatory domain which are in factory default state will scan for several minutes after booting. An IAP mesh point in factory default state will automatically join the portal if only a single Instant mesh network is found. In addition, the auto-join feature must be enabled in the existing network. NOTE: The IAP mesh point will get an IP address from the same DHCP pool as the portal, and this DHCP request goes through the portal. Dell PowerConnect W-Series Instant Access Point 6.1.2.3-2.0.0.0 | User Guide Mesh Network | 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
Dell PowerConnect W-Series Instant Access Point 6.1.2.3-2.0.0.0
| User Guide
Mesh Network
|
57
Figure 36
Login Window
7.
Create a new SSID and wpa-2 personal keys with
unrestricted
or
network based
access rules. Select
any permit
for basic connectivity.
8.
Connect a client to the new SSID and disconnect from the
instant
SSID.
9.
All the IAPs will show up on the Virtual Controller as shown in the figure below. Disconnect the IAPs that you
want to deploy as Mesh Points from the switch and place the IAPs at the desired location. The wired IAPs are
Mesh Portals.
Figure 37
Mesh Portal
NOTE: The IAPs in US, JP, or IL regulatory domain which are in factory default state will scan for several minutes after booting. An
IAP mesh point in factory default state will automatically join the portal if only a single Instant mesh network is found. In addition,
the auto-join feature must be enabled in the existing network.
NOTE: The IAP mesh point will get an IP address from the same DHCP pool as the portal, and this DHCP request goes through the
portal.