Dell PowerEdge R830 Owners Manual - Page 135

Installing the network daughter card, Installing the NDC

Get Dell PowerEdge R830 PDF manuals and user guides View all Dell PowerEdge R830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 135 highlights

Installing the network daughter card on page 135 Removing an expansion card from expansion card riser 2 on page 121 After working inside your system on page 64 Installing the network daughter card Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. 3. If applicable, remove the expansion card riser 1. 4. Keep the Phillips #1 screwdriver ready. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1. Orient the network daughter card (NDC) so that the Ethernet connectors fit through the slot in the back panel. 2. Align the captive screws on the card with the captive screw sockets on the system board. 3. Press the touch points on the card until the card connector is firmly seated on the system board connector. 4. Tighten the captive screws to secure the NDC to the system board. Figure 66. Installing the NDC 1. captive screw socket (2) 3. captive screw (2) 5. network daughter card (NDC) 2. connector on the system board 4. touch point (2) 6. back panel slot for Ethernet connectors Installing and removing system components 135

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
Installing the network daughter card
on page 135
Removing an expansion card from expansion card riser 2
on page 121
After working inside your system
on page 64
Installing the network daughter card
Prerequisites
1.
Follow the safety guidelines listed in the Safety instructions section.
2.
Follow the procedure listed in the Before working inside your system section.
3.
If applicable, remove the expansion card riser 1.
4.
Keep the Phillips #1 screwdriver ready.
CAUTION:
Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that are shipped with your product.
Steps
1.
Orient the network daughter card (NDC) so that the Ethernet connectors fit through the slot in the back panel.
2.
Align the captive screws on the card with the captive screw sockets on the system board.
3.
Press the touch points on the card until the card connector is firmly seated on the system board connector.
4.
Tighten the captive screws to secure the NDC to the system board.
Figure 66. Installing the NDC
1.
captive screw socket (2)
2.
connector on the system board
3.
captive screw (2)
4.
touch point (2)
5.
network daughter card (NDC)
6.
back panel slot for Ethernet connectors
Installing and removing system components
135