Dell PowerEdge R830 Owners Manual - Page 157

Installing the control panel

Get Dell PowerEdge R830 PDF manuals and user guides View all Dell PowerEdge R830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 157 highlights

Related tasks Before working inside your system on page 64 Installing the control panel on page 157 After working inside your system on page 64 Installing the control panel Prerequisites 1. Follow the safety guidelines listed in the Safety instructions section. 2. Follow the procedure listed in the Before working inside your system section. 3. Keep the #2 Phillips screwdriver ready. CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that are shipped with your product. Steps 1. Replace the blank information tag in the new control panel with the information tag retained from the old control panel. NOTE: Information tag lists system information such as Service Tag, NIC, and MAC address. 2. If disengaged, install the vFlash connector/USB connector module into the control panel using the following steps: a. Connect the control panel cable to the control panel. b. Install the screws to attach the vFlash connector/USB connector module to the control panel. Figure 90. Installing the vFlash connector/USB connector module i. vFlash connector/USB connector module ii. screw (2) iii. control panel connector cable 3. To install the information tag, push the information tag into the control panel slot. 4. Connect all the applicable cables to the system board. Installing and removing system components 157

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
Related tasks
Before working inside your system
on page 64
Installing the control panel
on page 157
After working inside your system
on page 64
Installing the control panel
Prerequisites
1.
Follow the safety guidelines listed in the Safety instructions section.
2.
Follow the procedure listed in the Before working inside your system section.
3.
Keep the #2 Phillips screwdriver ready.
CAUTION:
Many repairs may only be done by a certified service technician. You should only perform
troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or
telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by
your warranty. Read and follow the safety instructions that are shipped with your product.
Steps
1.
Replace the blank information tag in the new control panel with the information tag retained from the old control panel.
NOTE:
Information tag lists system information such as Service Tag, NIC, and MAC address.
2.
If disengaged, install the vFlash connector/USB connector module into the control panel using the following steps:
a.
Connect the control panel cable to the control panel.
b.
Install the screws to attach the vFlash connector/USB connector module to the control panel.
Figure 90. Installing the vFlash connector/USB connector module
i.
vFlash connector/USB connector module
ii.
screw (2)
iii.
control panel connector cable
3.
To install the information tag, push the information tag into the control panel slot.
4.
Connect all the applicable cables to the system board.
Installing and removing system components
157