Dell PowerEdge R830 Owners Manual - Page 73

Removing the filler bracket from the QPI connector

Get Dell PowerEdge R830 PDF manuals and user guides View all Dell PowerEdge R830 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

3. Follow the procedure listed in the Before working inside your system section. 4. If applicable, remove the cooling shroud. Retain the cooling shroud for future use. Steps 1. If applicable, remove the filler bracket. To remove the filler bracket, hold the tabs and lift the filler bracket away from the QPI connector. Figure 20. Removing the filler bracket from the QPI connector a. filler bracket b. standoff (2) 2. If applicable, remove the PEM power connector cap. 3. By holding the support pin and the release lever, align the alignment guides on the PEM with the alignment guides on the chassis, and lower the PEM into the chassis. Installing and removing system components 73

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
3.
Follow the procedure listed in the Before working inside your system section.
4.
If applicable, remove the cooling shroud. Retain the cooling shroud for future use.
Steps
1.
If applicable, remove the filler bracket. To remove the filler bracket, hold the tabs and lift the filler bracket away from the
QPI connector.
Figure 20. Removing the filler bracket from the QPI connector
a.
filler bracket
b.
standoff (2)
2.
If applicable, remove the PEM power connector cap.
3.
By holding the support pin and the release lever, align the alignment guides on the PEM with the alignment guides on the
chassis, and lower the PEM into the chassis.
Installing and removing system components
73