Home » Dell Manuals » Servers » Dell PowerEdge R830 » Manual Viewer

Dell PowerEdge R830 Owners Manual - Page 38

Boot Settings details, Choosing the system boot mode

View all Dell PowerEdge R830 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 38 highlights

Related tasks Boot Settings details on page 38 Changing the boot order on page 39 Boot Settings details About this task The Boot Settings screen details are explained as follows: Option Boot Mode Description Enables you to set the boot mode of the system. CAUTION: Switching the boot mode may prevent the system from booting if the operating system is not installed in the same boot mode. If the operating system supports UEFI, you can set this option to UEFI. Setting this field to BIOS allows compatibility with non-UEFI operating systems. This option is set to BIOS by default. NOTE: Setting this field to UEFI disables the BIOS Boot Settings menu. Setting this field to BIOS disables the UEFI Boot Settings menu. Boot Sequence Retry Hard-Disk Failover Boot Option Settings BIOS Boot Settings Enables or disables the Boot Sequence Retry feature. If this option is set to Enabled and the system fails to boot, the system reattempts the boot sequence after 30 seconds. This option is set to Enabled by default. Specifies the hard drive that is booted in the event of a hard drive failure. The devices are selected in the Hard-Disk Drive Sequence on the Boot Option Setting menu. When this option is set to Disabled, only the first hard drive in the list is attempted to boot. When this option is set to Enabled, all hard drives are attempted to boot in the order selected in the Hard-Disk Drive Sequence. This option is not enabled for UEFI Boot Mode. Configures the boot sequence and the boot devices. Enables or disables BIOS boot options. NOTE: This option is enabled only if the boot mode is BIOS. UEFI Boot Settings Enables or disables UEFI Boot options. The Boot options include IPv4 PXE and IPv6 PXE. This option is set to IPv4 by default. NOTE: This option is enabled only if the boot mode is UEFI. Related references Boot Settings on page 37 Choosing the system boot mode on page 38 Related tasks Viewing Boot Settings on page 37 Changing the boot order on page 39 Choosing the system boot mode System Setup enables you to specify one of the following boot modes for installing your operating system: ● BIOS boot mode (the default) is the standard BIOS-level boot interface. ● Unified Extensible Firmware Interface (UEFI) (the default) boot mode is an enhanced 64-bit boot interface. If you have configured your system to boot to UEFI mode, it replaces the system BIOS. 1. From the System Setup Main Menu, click Boot Settings, and select Boot Mode. 2. Select the boot mode you want the system to boot into. 38 Pre-operating system management applications

Section	Page
Dell PowerEdge R830 Owner's Manual	3
Dell PowerEdge R830 overview	8
Supported configurations for the PowerEdge R830 system	8
Front panel	10
2.5 inch hard drive chassis	10
LCD panel	12
Viewing Home screen	13
Setup menu	13
View menu	13
Back panel	14
Diagnostic indicators on the front panel	15
Hard drive indicator codes	17
NIC indicator codes	18
Power supply unit indicator codes	18
Locating service tag of your system	20
Documentation resources	21
Technical specifications	24
System dimensions	24
Chassis weight	25
Processor specifications	25
PSU specifications	25
System battery specifications	25
Expansion bus specifications	25
Memory specifications	26
Drive specifications	26
Hard drives	26
Optical drive	26
Ports and connectors specifications	26
USB ports	26
NIC ports	26
Serial connector	27
VGA ports	27
Internal Dual SD Module	27
Video specifications	27
Environmental specifications	27
Particulate and gaseous contamination specifications	28
Standard operating temperature	29
Expanded operating temperature	29
Expanded operating temperature restrictions	30
Initial system setup and configuration	31
Setting up your system	31
iDRAC configuration	31
Options to set up iDRAC IP address	31
Log in to iDRAC	32
Options to install the operating system	32
Methods to download firmware and drivers	32
Downloading the drivers and firmware	33
Pre-operating system management applications	34
Options to manage the pre-operating system applications	34
System Setup	34
Viewing System Setup	35
System Setup details	35
System BIOS	35
Viewing System BIOS	36
System BIOS Settings details	36
Boot Settings	37
Viewing Boot Settings	37
Boot Settings details	38
Choosing the system boot mode	38
Changing the boot order	39
Network Settings	39
Viewing Network Settings	40
Network Settings screen details	40
UEFI iSCSI Settings	40
Viewing UEFI iSCSI Settings	41
UEFI iSCSI Settings details	41
System Security	41
Viewing System Security	42
System Security Settings details	42
Creating a system and setup password	43
Using your system password to secure your system	44
Deleting or changing system and setup password	44
Operating with a setup password enabled	44
System Information	45
Viewing System Information	45
System Information details	45
Memory Settings	46
Viewing Memory Settings	46
Memory Settings details	47
Processor Settings	48
Viewing Processor Settings	48
Processor Settings details	48
SATA Settings	50
Viewing SATA Settings	50
SATA Settings details	50
Integrated Devices	53
Viewing Integrated Devices	53
Integrated Devices details	53
Serial Communication	54
Viewing Serial Communication	55
Serial Communication details	55
System Profile Settings	56
Viewing System Profile Settings	56
System Profile Settings details	56
Miscellaneous Settings	58
Viewing Miscellaneous Settings	58
Miscellaneous Settings details	58
iDRAC Settings utility	59
Entering the iDRAC Settings utility	59
Changing the thermal settings	60
Device Settings	60
Dell Lifecycle Controller	60
Embedded systems management	60
Boot Manager	60
Viewing Boot Manager	61
Boot Manager main menu	61
One-shot BIOS boot menu	61
System Utilities	61
PXE boot	62
Installing and removing system components	63
Safety instructions	63
Before working inside your system	64
After working inside your system	64
Recommended tools	64
Front bezel (optional)	65
Removing the optional front bezel	65
Installing the optional front bezel	66
System cover	66
Removing the system cover	66
Installing the system cover	67
Inside the system	69
Processor expansion module (optional)	70
Removing the processor expansion module	70
Installing the processor expansion module	72
Cooling shroud	76
Removing the cooling shroud	76
Installing the cooling shroud	77
Cooling fans	78
Removing a cooling fan	79
Installing a cooling fan	80
Cooling fan assembly	80
Removing the cooling fan assembly	80
Installing the cooling fan assembly	81
System memory	83
General memory module installation guidelines	85
Mode-specific guidelines	85
Advanced Error Correction Code	85
Memory optimized independent channel mode	86
Memory sparing	86
Memory mirroring	86
Sample memory configurations	86
Removing memory modules	91
Installing memory modules	92
Processors and heat sinks	94
Removing a heat sink	94
Removing a processor	95
Installing a processor	99
Installing a heat sink	101
Power supply units	102
Hot spare feature	103
Removing the power supply unit blank	103
Installing the power supply unit blank	104
Removing an AC power supply unit	105
Installing an AC power supply unit	106
Integrated storage controller card	107
Removing the integrated storage controller card	107
Installing the integrated storage controller card	108
Expansion cards and expansion card riser	110
Expansion card installation guidelines	110
Removing expansion card risers	111
Installing expansion card risers	115
Removing an expansion card from expansion card riser 1	118
Installing an expansion card into expansion card riser 1	120
Removing an expansion card from expansion card riser 2	121
Installing an expansion card into expansion card riser 2	123
Removing an expansion card from the expansion card riser 3	124
Installing an expansion card into expansion card riser 3	126
IDSDM	128
Removing an internal SD card	129
Installing an internal SD card	130
Removing the optional internal dual SD module	131
Installing the optional internal dual SD module	132
Network daughter card	133
Removing the network daughter card	133
Installing the network daughter card	135
Internal USB memory key (optional)	136
Replacing the optional internal USB memory key	136
System battery	137
Replacing the system battery	137
Hard drives	139
Removing a hot swappable hard drive or solid state drive	139
Installing a hot swappable hard drive or solid state drive	140
Removing a 2.5-inch hard drive blank	141
Installing a 2.5-inch hard drive blank	142
Removing a hard drive or a solid state drive from a hard drive carrier	143
Installing a hard drive or solid state drives into a hard drive carrier	143
Optical drive (optional)	144
Removing the optical drive	144
Installing the optical drive	145
Removing the slim optical drive blank	146
Installing the slim optical drive blank	147
Hard drive backplane	148
Removing the hard drive backplane	148
Installing the hard drive backplane	153
Control panel	154
Removing the control panel	154
Installing the control panel	157
System board	159
Removing the system board	159
Installing the system board	161
Entering the system Service Tag by using System Setup	163
Restoring the Service Tag by using the Easy Restore feature	163
Trusted Platform Module	163
Installing the Trusted Platform Module	164
Initializing the TPM for BitLocker users	165
Initializing the TPM for TXT users	165
Using system diagnostics	166
Dell Embedded System Diagnostics	166
When to use the Embedded System Diagnostics	166
Running the Embedded System Diagnostics from Boot Manager	166
Running the Embedded System Diagnostics from the Dell Lifecycle Controller	166
System diagnostic controls	167
Jumpers and connectors	168
System board jumper settings	168
System Board Connectors	169
Disabling forgotten password	171
Troubleshooting your system	173
Troubleshooting system startup failure	173
Troubleshooting external connections	173
Troubleshooting the video subsystem	174
Troubleshooting a USB device	174
Troubleshooting iDRAC Direct - USB XML configuration	175
Troubleshooting iDRAC Direct - Laptop connection	175
Troubleshooting a serial input and output device	176
Troubleshooting a NIC	176
Troubleshooting a wet system	177
Troubleshooting a damaged system	178
Troubleshooting the system battery	178
Troubleshooting power supply units	179
Troubleshooting power source problems	179
Troubleshooting power supply unit problems	179
Troubleshooting cooling problems	180
Troubleshooting cooling fans	180
Troubleshooting system memory	181
Troubleshooting an internal USB key	182
Troubleshooting a micro SD card	183
Troubleshooting an optical drive	183
Troubleshooting a tape backup unit	184
Troubleshooting a drive or SSD	184
Troubleshooting a storage controller	185
Troubleshooting expansion cards	186
Troubleshooting processors	187
System messages	187
Warning messages	187
Diagnostic messages	187
Alert messages	187
Getting help	188
Contacting Dell EMC	188
Documentation feedback	188
Accessing system information by using QRL	188

Match case Limit results 1 per page

Related tasks

Boot Settings details

on page 38

Changing the boot order

on page 39

Boot Settings details

About this task

The

Boot Settings

screen details are explained as follows:

Option

Description

Boot Mode

Enables you to set the boot mode of the system.

CAUTION:

Switching the boot mode may prevent the system from booting if the operating

system is not installed in the same boot mode.

If the operating system supports UEFI, you can set this option to

UEFI

. Setting this field to

BIOS

allows

compatibility with non-UEFI operating systems. This option is set to

BIOS

by default.

NOTE:

Setting this field to

UEFI

disables the

BIOS Boot Settings

menu. Setting this field to

BIOS

disables the

UEFI Boot Settings

menu.

Boot Sequence

Retry

Enables or disables the Boot Sequence Retry feature. If this option is set to

Enabled

and the system fails

to boot, the system reattempts the boot sequence after 30 seconds. This option is set to

Enabled

default.

Hard-Disk

Failover

Specifies the hard drive that is booted in the event of a hard drive failure. The devices are selected in the

Hard-Disk Drive Sequence

on the

Boot Option Setting

menu. When this option is set to

Disabled

only the first hard drive in the list is attempted to boot. When this option is set to

Enabled

, all hard drives

are attempted to boot in the order selected in the

Hard-Disk Drive Sequence

. This option is not enabled

for UEFI Boot Mode.

Boot Option

Settings

Configures the boot sequence and the boot devices.

BIOS Boot

Settings

Enables or disables BIOS boot options.

NOTE:

This option is enabled only if the boot mode is BIOS.

UEFI Boot

Settings

Enables or disables UEFI Boot options. The Boot options include

IPv4 PXE

and

IPv6 PXE

. This option is

set to

IPv4

by default.

NOTE:

This option is enabled only if the boot mode is UEFI.

Related references

Boot Settings

on page 37

Choosing the system boot mode

on page 38

Related tasks

Viewing Boot Settings

on page 37

Changing the boot order

on page 39

Choosing the system boot mode

System Setup enables you to specify one of the following boot modes for installing your operating system:

●

BIOS boot mode (the default) is the standard BIOS-level boot interface.

●

Unified Extensible Firmware Interface (UEFI) (the default) boot mode is an enhanced 64-bit boot interface. If you have

configured your system to boot to UEFI mode, it replaces the system BIOS.

From the

System Setup Main Menu

, click

Boot Settings

, and select

Boot Mode

Select the boot mode you want the system to boot into.

Pre-operating system management applications