Epson PowerLite 8150i Administrator's Manual - Page 88

Maintaining and Transporting the Projector, loosening the screws, lift off the lamp cover.

Get Epson PowerLite 8150i PDF manuals and user guides View all Epson PowerLite 8150i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

Follow these steps to replace the lamp: 1. Turn off the projector and unplug the power cable. 2. Allow the projector to cool down for at least an hour (if it has been on). 3. Use a screwdriver to loosen the two retaining screws on the lamp cover. (You cannot remove these screws from the cover.) After loosening the screws, lift off the lamp cover. warning Let the lamp cool before replacing it. If the lamp breaks, handle the shards carefully to avoid injury. 4. Use a screwdriver to loosen the three screws holding the lamp in place. (You cannot remove these screws.) handle 5. Lift up the handle and pull out the lamp. Maintaining and Transporting the Projector 87

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
Maintaining and Transporting the Projector
87
Follow these steps to replace the lamp:
1.
Turn off the projector and unplug the power cable.
2.
Allow the projector to cool down for at least an hour (if it has
been on).
3.
Use a screwdriver to loosen the two retaining screws on the lamp
cover. (You cannot remove these screws from the cover.) After
loosening the screws, lift off the lamp cover.
4.
Use a screwdriver to loosen the three screws holding the lamp in
place. (You cannot remove these screws.)
5.
Lift up the handle and pull out the lamp.
warning
Let the lamp cool before
replacing it. If the lamp
breaks, handle the shards
carefully to avoid injury.
handle