Epson Stylus Pro 10000 - Photographic Dye Ink User Manual - Page 59

Adjusting the Platen Gap for Heavy Stock, automatically. However

Get Epson Stylus Pro 10000 - Photographic Dye Ink - Stylus Pro 10000 Print Engine PDF manuals and user guides View all Epson Stylus Pro 10000 - Photographic Dye Ink manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Caution Handling Paper and Other Media | 2-13 8. Push the paper set lever all the way in, then close the lower cover. PRESS PAUSE BUTTON appears on the control panel display. To avoid damaging the printer, never move the paper set lever while the Operate or Pause light is flashing. 9. Press the Pause button. The print head moves and the board feeds into printing position automatically. READY appears on the control panel. (Even if you don't press Pause, the board and printer will move into printing position automatically after 10 seconds.) 10. Run your print job. After it is finished, the posterboard stays in the printer. 11. To remove the print, hold it and pull the paper set lever all the way out. Adjusting the Platen Gap for Heavy Stock When you print on heavy stock, you may need to adjust the platen gap setting. Normally, the AUTO setting allows the printer to adjust automatically. However, if print quality is not satisfactory when you use heavy stock, change this setting to WIDE. Follow these steps: 1. Press the SelecType button. PRINTER SETTING MENU appears on the display. 2. Press the Item button. PLATEN GAP=AUTO appears on the display. 3. Press the + button. PLATEN GAP=WIDE appears on the display. 2-13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
2-13
Handling Paper and Other Media
|
2-13
8.
Push the paper set lever all the way in, then close the lower cover.
PRESS PAUSE BUTTON
appears on the control panel display.
9.
Press the
Pause
button. The print head moves and the board feeds into
printing position automatically.
READY
appears on the control panel.
(Even if you don’t press
Pause
, the board and printer will move into
printing position automatically after 10 seconds.)
10.
Run your print job. After it is finished, the posterboard stays in the
printer.
11.
To remove the print, hold it and pull the paper set lever all the way out.
Adjusting the Platen Gap for Heavy Stock
When you print on heavy stock, you may need to adjust the platen gap
setting. Normally, the
AUTO
setting allows the printer to adjust
automatically. However, if print quality is not satisfactory when you use
heavy stock, change this setting to
WIDE.
Follow these steps:
1.
Press the
SelecType
button.
PRINTER SETTING MENU
appears on
the display.
2.
Press the
Item
button.
PLATEN GAP=AUTO
appears on the display.
3.
Press the
+
button.
PLATEN GAP=WIDE
appears on the display.
Caution
To avoid damaging the
printer, never move the
paper set lever while the
Operate
or
Pause
light
is flashing.