HP Workstation x1000 hp workstations general - adaptec RAID installation guide - Page 103

persists, contact Adaptec Technical Support.

Get HP Workstation x1000 PDF manuals and user guides View all HP Workstation x1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 103 highlights

troubleshooting LED Pattern 7, 6, 5, 3, 1 7, 6, 5, 3, 2, 1 Problem Too much memory Wrong-sized memory Description Adaptec 2400A/2100S/3200S/3400S only- The controller has more than 128 MB of memory. Install a correct memory module of 32, 64, or 128 MB. A memory module other than 32, 64, or 128 MB has been detected. Install a correct memory module. The controller fails to respond and various IRQ LEDs in the 1-4 range flash once per second. This LED pattern indicates an internal microprocessor error occurred in the controller. Shut down the computer and unplug all cables. Restart the computer. If the condition does not reappear, reconnect the cables and devices, one device at a time, until the faulty hard drive or cable is isolated. If the error persists, contact Adaptec Technical Support. Pressing Ctrl+A to access SMOR does not work or the information displayed is garbled. Reset the NVRAM to the default settings and reconfigure the RAID. To reset the NVRAM, refer to Appendix D. After updating the Adaptec controller firmware or BIOS and restarting, the controller does not respond. The update may have been unsuccessful. Reset the NVRAM to the default settings and reconfigure the RAID. To reset the NVRAM, refer to Appendix D. During the installation of SCO UNIX with the Adaptec controller as the boot controller, the following message appears: Warning: Controller cannot install interrupts vecno=xx, type=2, IPL=5 Vector xx is private. SCO UNIX reserves certain interrupts for its internal use. This error indicates that the Adaptec controller has been assigned one of these reserved interrupts. Assign a different interrupt to the controller and start the installation again. C-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
C-3
troubleshooting
The controller fails to respond and various IRQ LEDs in the 1–4
range flash once per second.
This LED pattern indicates an internal microprocessor error
occurred in the controller. Shut down the computer and unplug
all cables. Restart the computer. If the condition does not
reappear, reconnect the cables and devices, one device at a time,
until the faulty hard drive or cable is isolated. If the error
persists, contact Adaptec Technical Support.
Pressing Ctrl+A to access SMOR does not work or the
information displayed is garbled.
Reset the NVRAM to the default settings and reconfigure the
RAID. To reset the NVRAM, refer to
Appendix D
.
After updating the Adaptec controller firmware or BIOS and
restarting, the controller does not respond.
The update may have been unsuccessful.
Reset the NVRAM to the
default settings and reconfigure the RAID. To reset the NVRAM,
refer to
Appendix D
.
During the installation of SCO UNIX with the Adaptec controller
as the boot controller, the following message appears:
Warning: Controller cannot install interrupts vecno=xx, type=2,
IPL=5 Vector xx is private.
SCO UNIX reserves certain interrupts for its internal use. This
error indicates that the Adaptec controller has been assigned one
of these reserved interrupts. Assign a different interrupt to the
controller and start the installation again.
7, 6, 5, 3, 1
Too much
memory
Adaptec 2400A/2100S/3200S/3400S only
—
The controller has more than 128 MB of
memory. Install a correct memory
module of 32, 64, or 128 MB.
7, 6, 5, 3, 2, 1
Wrong-sized
memory
A memory module other than 32, 64, or
128 MB has been detected. Install a
correct memory module.
LED Pattern
Problem
Description