HP Workstation x1000 hp workstations general - adaptec RAID installation guide - Page 58

installing the driver in a existing NetWare 4.11, server

Get HP Workstation x1000 PDF manuals and user guides View all HP Workstation x1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 58 highlights

Adaptec RAID Installation Guide 7 Insert the NetWare 4.11 CD. 8 Insert the driver disk you created in Step 1 and run dpt411.bat. This utility copies the necessary files to the C drive. 9 Run install.bat from the C drive. 10 When asked to select a disk driver select i2opci.nlm. Enter the slot number where the controller is installed and press F10. 11 Select Save parameters and load driver. 12 Select Yes to select another driver. 13 Select bkstrosm.ham. Enter the slot number where the controller is installed and press F10. 14 Select Save parameters and load driver. 15 Install any additional drivers and continue the installation. 16 Select Edit startup.ncf. If needed, edit the file so that i2opci.nlm is listed before bkstrosm.ham in your startup.ncf file. 17 Continue with the NetWare installation according to the Novell documentation. 18 Upgrade your NetWare version to the minimum patch level specified by Novell. installing the driver in a existing NetWare 4.11 server In this scenario, you are integrating an Adaptec RAID controller into an existing NetWare 4.11 server as a secondary controller. To install the driver 1 Upgrade your existing NetWare server to the minimum patch level specified by Novell. 2 Create a driver floppy disk using the Adaptec RAID Installation CD. To create the disk 3-20

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
3-20
Adaptec RAID Installation Guide
7
Insert the NetWare 4.11 CD.
8
Insert the driver disk you created in
Step 1
and run
dpt411.bat
. This utility copies the necessary files to the
C
drive.
9
Run
install.bat
from the
C
drive.
10
When asked to select a disk driver select
i2opci.nlm
. Enter
the slot number where the controller is installed and press
F10
.
11
Select
Save parameters and load driver
.
12
Select
Yes
to select another driver.
13
Select
bkstrosm.ham
. Enter the slot number where the
controller is installed and press
F10
.
14
Select
Save parameters and load driver
.
15
Install any additional drivers and continue the installation.
16
Select
Edit startup.ncf
. If needed, edit the file so that
i2opci.nlm
is listed before
bkstrosm.ham
in your
startup.ncf
file.
17
Continue with the NetWare installation according to the
Novell documentation.
18
Upgrade your NetWare version to the minimum patch level
specified by Novell.
installing the driver in a existing NetWare 4.11
server
In this scenario, you are integrating an Adaptec RAID controller
into an existing NetWare 4.11 server as a secondary controller. To
install the driver
1
Upgrade your existing NetWare server to the minimum
patch level specified by Novell.
2
Create a driver floppy disk using the
Adaptec RAID
Installation CD
.
To create the disk