HP Workstation x1000 hp workstations general - adaptec RAID installation guide - Page 66

adding the Ccontroller to an existing, OpenDesktop 3.x or OpenServer 5.x system, adding

Get HP Workstation x1000 PDF manuals and user guides View all HP Workstation x1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

Adaptec RAID Installation Guide % adapter type=dpti ha=0 id=7 channel=0, PCI 6 Continue the installation according to the SCO documentation. Note: If you are installing from tape or CD, OpenServer 5.x locates the tape or CD automatically. adding the Ccontroller to an existing OpenDesktop 3.x or OpenServer 5.x system In this scenario, you are adding an Adaptec RAID controller to an existing Open Desktop 3.x or OpenServer 5.x system. To install the driver 1 Install and configure your Adaptec RAID controller and hard drives according to the instructions in Chapter 2. 2 Boot SCO UNIX. 3 After SCO UNIX has booted, insert the driver disk you created earlier (refer to page 3-26). 4 To run the installpkg utility, type installpkg -d disk/. SCO UNIX reads the disk and prompts you to enter the package name to be installed. 5 Type dpti4 for Open Desktop 3.x and dpti5 for SCO OpenServer 5.x. 6 After the package is installed, rebuild the kernel. 7 Restart the system. 8 Install the new kernel. 9 Add devices to the controller. adding the controller to an existing UnixWare 7 system In this scenario, you are adding an Adaptec RAID controller to an existing UnixWare 7 system. To install the driver 3-28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
3-28
Adaptec RAID Installation Guide
% adapter type=dpti ha=0 id=7 channel=0, PCI
6
Continue the installation according to the SCO
documentation.
Note:
If you are installing from tape or CD,
OpenServer 5.
x
locates the tape or CD automatically.
adding the Ccontroller to an existing
OpenDesktop 3.x or OpenServer 5.x system
In this scenario, you are adding an Adaptec RAID controller to an
existing Open Desktop 3.
x
or OpenServer 5.
x
system. To install
the driver
1
Install and configure your Adaptec RAID controller and
hard drives according to the instructions in
Chapter 2
.
2
Boot SCO UNIX.
3
After SCO UNIX has booted, insert the driver disk you
created earlier (refer to
page 3-26
).
4
To run the
installpkg
utility, type
installpkg -d disk/
.
SCO UNIX reads the disk and prompts you to enter the
package name to be installed.
5
Type
dpti4
for Open Desktop 3.
x
and
dpti5
for SCO
OpenServer 5.
x
.
6
After the package is installed, rebuild the kernel.
7
Restart the system.
8
Install the new kernel.
9
Add devices to the controller.
adding the controller to an existing UnixWare 7
system
In this scenario, you are adding an Adaptec RAID controller to an
existing UnixWare 7 system. To install the driver