HP Workstation x1000 hp workstations general - adaptec RAID installation guide - Page 41

adding the controller to an existing system

Get HP Workstation x1000 PDF manuals and user guides View all HP Workstation x1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

installing the driver e Insert a floppy disk and click OK. The system creates the driver disk. 3 Shut down the system and remove the Adaptec RAID Installation CD and the driver floppy disk. 4 Insert the Windows 2000 setup media (floppy disk or CD) and restart the system to begin the Windows 2000 installation. 5 When the Windows 2000 installation starts, a blue screen appears after the hardware detection message. When prompted to install a third-party driver, press F6. Note: You only have 5 seconds to press the F6 key during the installation startup. A prompt appears at the bottom of the screen when F6 is active. Press F6 at this time; otherwise, you must restart the Windows 2000 installation process to complete this procedure correctly. 6 When Windows 2000 starts for the first time, it launches the Found New Hardware Wizard. Click Next. Then, select Search for suitable driver for my device and click Next again. 7 Insert the driver disk you created in Step 2. Select the floppy disk and click Next. The wizard should find the Adaptec RAID Adapter. 8 Click Next and follow the instructions. Eventually, the installation will require that the system shut down and restart. After the restart, respond to any further instructions as needed to complete the installation. adding the controller to an existing system In this scenario, you are adding an Adaptec RAID controller to a system that already has a Windows 2000 operating system. To install the driver 1 Create a driver floppy disk using the Adaptec RAID Installation CD. To create the disk a Insert the Adaptec RAID Installation CD in your drive. 3-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
3-3
installing the driver
e
Insert a floppy disk and click
OK
. The system creates the
driver disk.
3
Shut down the system and remove the
Adaptec RAID
Installation CD
and the driver floppy disk.
4
Insert the Windows 2000 setup media (floppy disk or CD)
and restart the system to begin the Windows 2000
installation.
5
When the Windows 2000 installation starts, a blue screen
appears after the hardware detection message. When
prompted to install a third-party driver, press
F6
.
Note:
You only have 5 seconds to press the F6 key during
the installation startup. A prompt appears at the bottom
of the screen when F6 is active. Press
F6
at this time;
otherwise, you must restart the Windows 2000
installation process to complete this procedure correctly.
6
When Windows 2000 starts for the first time, it launches the
Found New Hardware Wizard. Click
Next
. Then, select
Search for suitable driver for my device
and click
Next
again.
7
Insert the driver disk you created in
Step 2
. Select the
floppy disk and click
Next
. The wizard should find the
Adaptec RAID Adapter
.
8
Click
Next
and follow the instructions. Eventually, the
installation will require that the system shut down and
restart. After the restart, respond to any further
instructions as needed to complete the installation.
adding the controller to an existing system
In this scenario, you are adding an Adaptec RAID controller to a
system that already has a Windows 2000 operating system. To
install the driver
1
Create a driver floppy disk using the
Adaptec RAID
Installation CD
. To create the disk
a
Insert the
Adaptec RAID Installation CD
in your drive.