HP Workstation x1000 hp workstations general - adaptec RAID installation guide - Page 59

installing the driver for a boot controller in a new, NetWare 4.2 server

Get HP Workstation x1000 PDF manuals and user guides View all HP Workstation x1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

installing the driver a Insert the Adaptec RAID Installation CD in your drive and a blank floppy disk in the floppy disk drive. b Copy all the files in \packages\netware\4.11\driver to the floppy disk. c Remove the Adaptec RAID Installation CD and the driver floppy disk. 3 Shutdown the server. 4 Install and configure your Adaptec RAID controller as a secondary controller according to the instructions in Chapter 2. Note the slot occupied by the controller; you will need this information later in the install process. 5 Start up the server. During restart, press Ctrl+A to start SMOR. Use SMOR to create the RAID. For details, refer to using SMOR on page 2-11. 6 Start NetWare. 7 When the console prompt appears, type load install and press Enter. 8 Select Product Options and press Enter. 9 Select Install a Product Not Listed and press Enter. 10 Insert the disk you created in Step 2 and install I2O and Block Storage support only. 11 Accept the defaults for the remaining install options. 12 Return to the main install screen and select NCF Options. 13 Select Edit startup.ncf. If needed, edit the file so that i2opci.nlm is listed before bkstrosm.ham in your startup.ncf file. 14 Shutdown and restart the server. installing the driver for a boot controller in a new NetWare 4.2 server In this scenario, you are installing an Adaptec RAID controller as the boot controller in a new NetWare 4.2 server. To install the driver 3-21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
3-21
installing the driver
a
Insert the
Adaptec RAID Installation CD
in your drive
and a blank floppy disk in the floppy disk drive.
b
Copy all the files in
\packages\netware\4.11\driver
to the
floppy disk.
c
Remove the
Adaptec RAID Installation CD
and the driver
floppy disk.
3
Shutdown the server.
4
Install and configure your Adaptec RAID controller as a
secondary controller according to the instructions in
Chapter 2
. Note the slot occupied by the controller; you will
need this information later in the install process.
5
Start up the server. During restart, press
Ctrl+A
to start
SMOR. Use SMOR to create the RAID. For details, refer to
using SMOR
on page 2-11
.
6
Start NetWare.
7
When the console prompt appears, type load install and
press
Enter
.
8
Select
Product Options
and press
Enter
.
9
Select
Install a Product Not Listed
and press
Enter
.
10
Insert the disk you created in
Step 2
and install I
2
O and
Block Storage support only.
11
Accept the defaults for the remaining install options.
12
Return to the main install screen and select
NCF Options.
13
Select
Edit startup.ncf
. If needed, edit the file so that
i2opci.nlm
is listed before
bkstrosm.ham
in your
startup.ncf
file.
14
Shutdown and restart the server.
installing the driver for a boot controller in a new
NetWare 4.2 server
In this scenario, you are installing an Adaptec RAID controller as
the boot controller in a new NetWare4.2 server. To install the
driver