HP Workstation x1000 hp workstations general - adaptec RAID installation guide - Page 107

Create, Driver Disk

Get HP Workstation x1000 PDF manuals and user guides View all HP Workstation x1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

controller reset procedures 4 When you see the Adaptec splash screen, click Create Driver Disk. Then, click the appropriate menu option. 5 Insert a floppy disk and click OK. The system creates the bootable SMOR disk. 6 Remove the Adaptec RAID Installation CD and the driver floppy disk. 7 Shut down the system. 8 If necessary, reinstall the controller in your system. Now, to reset the controller firmware, BIOS, and SMOR, perform the following tasks: 1 Install a jumper on flash mode 0 jumper connector. For the location of the jumper connector, refer to Appendix A. 2 Insert the SMOR boot disk and boot the system. SMOR starts. 3 Use SMOR to flash the controller firmware. 4 Shut down the system. 5 Remove the jumper you installed in Step 1. 6 Remove the SMOR boot disk. 7 Reboot the system from the SMOR boot disk. If the system restarts normally, the controller can now be configured using SMOR or Storage Manager. 8 Use SMOR to flash the controller BIOS and SMOR images. If the system fails to restart, call Adaptec Technical Support. D-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
D-3
controller reset procedures
4
When you see the Adaptec splash screen, click
Create
Driver Disk
. Then, click the appropriate menu option.
5
Insert a floppy disk and click
OK
. The system creates the
bootable SMOR disk.
6
Remove the
Adaptec RAID Installation CD
and the driver
floppy disk.
7
Shut down the system.
8
If necessary, reinstall the controller in your system.
Now, to reset the controller firmware, BIOS, and SMOR, perform
the following tasks:
1
Install a jumper on flash mode 0 jumper connector. For the
location of the jumper connector, refer to
Appendix A
.
2
Insert the SMOR boot disk and boot the system. SMOR
starts.
3
Use SMOR to flash the controller firmware.
4
Shut down the system.
5
Remove the jumper you installed in
Step 1
.
6
Remove the SMOR boot disk.
7
Reboot the system from the SMOR boot disk. If the system
restarts normally, the controller can now be configured
using SMOR or Storage Manager.
8
Use SMOR to flash the controller BIOS and SMOR images.
If the system fails to restart, call Adaptec Technical Support.