Home » Lantronix Manuals » Electronics Accessories » Lantronix SLB » Manual Viewer

Lantronix SLB Lantronix SLB - User Guide - Page 210

Apply, Parameters, Location for Save, Restore, or Manage, Local Disk - Saved Configurations

Add to My Manuals
Save this manual to your list of manuals

Page 210 highlights

12: Maintenance Location for Save, Restore, or Manage 3. Click Apply. If you selected to save or restore a configuration, select one of the following options:  Local Disk - Saved Configurations: If restoring, select a saved configuration from the drop-down list.  FTP Server: The FTP server specified in the FTP/SFTP/TFTP section. If you select this option, select FTP or SFTP to transfer the configuration file.  NFS Mounted Directory: Local directory of the NFS server for mounting files.  CIFS Share - Saved Configurations: If restoring, select a saved configuration from the drop-down list.  USB: If a USB thumb drive is loaded into one of the USB ports of the SLB , and properly mounted, the configuration can be saved to or restored from this location.If you select this option, select the port in which the USB thumb drive is mounted; then click a saved configuration from the drop-down list.  HTTPS: For saving, the browser will prompt the user to save the configuration. For restoring, the configuration will be uploaded to the Local Disk location.  Manage: The Manage option allows you to view and delete all configurations saved to the selected location. This feature is available for the default, CIFS Share, and USB locations. Note: If you selected an option that forces a reboot (restore configuration, update firmware, or reset factory defaults), the SLB automatically reboots at the end of the process. To set the acceptable range for the internal temperature sensor (an SNMP trap is sent if the temperature is outside of this range): set temperature Parameters: low high calibrate Note: the calibration offset will be applied one hour after setting the value. To display the acceptable range and the current reading from the internal temperature sensor: show temperature To set the acceptable range for the internal temperature sensor (an SNMP trap is sent if the temperature is outside of this range): set temperature low Parameters: low high calibrate Note: the calibration offset will be applied one hour after setting the value. SLB - Branch Office Manager User Guide 210

Section	Page
SLB - Branch Office Manager User Guide	1
Copyright & Trademark	2
Open Source Software	2
Contacts	2
Disclaimer & Revisions	2
Revision History	3
Table of Contents	4
List of Figures	13
List of Tables	16
1: About this Guide	17
Purpose and Audience	17
Summary of Chapters	17
Additional Documentation	18
2: Introduction	19
Features	19
Models	22
System Features	23
Application Example	24
Hardware Features	25
3: Installation	29
What's in the Box	29
Technical Specifications	30
Physical Installation	31
Typical Installations	35
4: Quick Setup	36
Recommendations	36
IP Address	36
Method #1 Using the Front Panel Display	37
Method #2 Quick Setup on the Web Page	40
Method #3 Quick Setup on the Command Line Interface	42
Next Step	45
5: Web and Command Line Interfaces	46
Web Interface	46
Command Line Interface	48
6: Basic Parameters	52
Requirements	52
IP Filter	58
IP Filter Commands	62
Routing	63
VPN	65
7: Services	68
System Logging and Other Services	68
SSH/Telnet/Logging	68
SNMP	72
NFS and SMB/CIFS	75
Secure Lantronix Network	77
Date and Time	82
Web Server	84
iGoogle Gadgets	88
8: Device Ports	90
Connection Methods	90
Permissions	90
Device Status	91
Global Port Settings	91
Device Ports - Settings	94
Interacting with a Device Port	106
Device Ports - Logging	107
Console Port	112
Power Outlets	114
Host Lists	117
Scripts	121
Sites	134
Modem Dialing States	137
9: USB Port	141
Set Up of USB Storage	141
Manage Firmware and Configuration Files	148
USB Commands	148
10: Connections	150
Typical Setup Scenarios for the SLB	150
11: User Authentication	157
Local and Remote User Settings	160
NIS	168
LDAP	171
RADIUS	176
Kerberos	182
TACACS+	186
Groups	190
SSH Keys	193
Custom Menus	199
12: Maintenance	206
SLB Maintenance	206
Audit Log	219
Email Log	220
Diagnostics	221
Status/Reports	225
Emailing Logs and Reports	227
Events	230
LCD/Keypad	232
Banners	234
13: Application Examples	236
Dial-in (Text Mode) to a Remote Device	238
Local Serial Connection to Network Device via Telnet	239
14: Command Reference	241
Introduction to Commands	241
Administrative Commands	243
Audit Log Commands	251
Authentication Commands	251
Kerberos Commands	252
LDAP Commands	253
Local Users Commands	254
NIS Commands	257
RADIUS Commands	258
TACACS+ Commands	259
User Permissions Commands	260
CLI Commands	262
Connection Commands	264
Custom User Menu Commands	267
Date and Time Commands	269
Device Commands	270
Device Port Commands	271
Diagnostic Commands	274
End Device Commands	276
Events Commands	277
Group Commands	278
Host List Commands	279
IP Filter Commands	280
Logging Commands	281
Network Commands	282
NFS and SMB/CIFS Commands	285
Power Commands	286
Routing Commands	287
Services Commands	288
SLB Network Commands	289
SSH Key Commands	290
Status Commands	292
System Log Commands	294
USB Storage Commands	294
USB Modem Commands	295
Appendix A: Bootloader	297
Accessing the Bootloader	297
Bootload Commands	297
Appendix B: Security Considerations	298
Security Practice	298
Factors Affecting Security	298
Appendix C: Safety Information	299
Safety Precautions	299
Appendix D: Adapters and Pinouts	301
Appendix E: Protocol Glossary	304

Match case Limit results 1 per page

12: Maintenance

SLB - Branch Office Manager User Guide

210

Click

Apply

Note:

If you selected an option that forces a reboot (restore configuration, update

firmware, or reset factory defaults), the SLB automatically reboots at the end of the

process.

To set the acceptable range for the internal temperature sensor (an SNMP trap is sent if the

temperature is outside of this range):

set temperature <one or more parameters>

Parameters:

low <Low Temperature in C.>

high <High Temperature in C.>

calibrate <Temperature Calibration in C.>

Note:

the calibration offset will be applied one hour after setting the value.

To display the acceptable range and the current reading from the internal temperature

sensor:

show temperature

To set the acceptable range for the internal temperature sensor (an SNMP trap is sent if the

temperature is outside of this range):

set temperature low <one or more parameters>

Parameters:

low <Low Temperature in C.>

high <High Temperature in C.>

calibrate <Temperature Calibration in C.>

Note:

the calibration offset will be applied one hour after setting the value.

Location for Save,

Restore, or Manage

If you selected to save or restore a configuration, select one of the following

options:



Local Disk – Saved Configurations:

If restoring, select a saved

configuration from the drop-down list.



FTP Server:

The FTP server specified in the FTP/SFTP/TFTP section. If you

select this option, select

FTP

SFTP

to transfer the configuration file.



NFS Mounted Directory:

Local directory of the NFS server for mounting

files.



CIFS Share – Saved Configurations:

If restoring, select a saved

configuration from the drop-down list.



USB:

If a USB thumb drive is loaded into one of the USB ports of the SLB ,

and properly mounted,

the configuration can be saved to or restored from

this location.If you select this option, select the port in which the USB thumb

drive is mounted; then click a saved configuration from the drop-down list.



HTTPS:

For saving, the browser will prompt the user to save the

configuration. For restoring, the configuration will be uploaded to the Local

Disk location.



Manage:

The

Manage

option allows you to view and delete all configurations

saved to the selected location. This feature is available for the default, CIFS

Share, and USB locations.