Lantronix SLB Lantronix SLB - User Guide - Page 54

6: Basic Parameters

SLB - Branch Office Manager User Guide

54

2.

Enter the following information:

Eth1 and Eth2 Settings

Note:

Configurations with the same IP subnet on multiple interfaces (Ethernet or PPP)

are not currently supported.

Eth 1 Settings

or

Eth 2 Settings



Disabled:

If selected, disables the network port.



Obtain from DHCP:

Acquires IP address, subnet mask, hostname and gateway

from the DHCP server. (The DHCP server may not provide the hostname

gateway, depending on its setup.) This is the default setting. If you select this

option, skip to Gateway.



Obtain from BOOTP:

Lets a network node request configuration information

from a BOOTP "server" node. If you select this option, skip to Gateway.



Specify:

Lets you manually assign a static IP address, generally provided by the

system administrator.

IP Address

(if specifying)



Enter an IP address that will be unique and valid on your network. There is no

default.



Enter all IP addresses in dot-quad notation. Do not use leading zeros in the

fields for dot-quad numbers less than 100. For example, if your IP address is

172.19.201.28, do not enter 028 for the last segment.

Note:

Currently, the SLB does not support configurations with the same IP subnet

on multiple interfaces (Ethernet or PPP).

Subnet Mask

If specifying an IP address, enter the network segment on which the SLB resides.

There is no default.

IPv6 Address

Address of the port in IPv6 format.

Note:

The SLB supports IPv6 connections for a limited set of services: the web,

SSH, and Telnet.

IPv6 addresses are written as 8 sets of 4-digit hexadecimal numbers separated by

colons. There are several rules for modifying the address. For example:

1234:0BCD:1D67:0000:0000:8375:BADD:0057

may be shortened to

1234:BCD:1D67::8375:BADD:57.

IPv6 Address

(Link Local)

An IPv6 address that is intended only for communications within the segment of a

local network.

Mode

Select the direction (full duplex or half-duplex) and speed (10 or 100Mbit) of data

transmission. The default is Auto, which allows the Ethernet port to auto-negotiate

the speed and duplex with the hardware endpoint to which it is connected.

MTU

Displays the multicast address of the Ethernet port.

Enable IPv6

Select this box to enable the IPv6 protocol. Disabled by default.

Ethernet Bonding

Ethernet 1 and Ethernet 2 can be bonded to support redundancy (Active Backup),

aggregation (802.3ad), and load balancing. Disabled by default. Note that if

Ethernet Bonding is enabled, assigning individual IP Addresses to Device Ports is

not supported.

Section	Page
SLB - Branch Office Manager User Guide	1
Copyright & Trademark	2
Open Source Software	2
Contacts	2
Disclaimer & Revisions	2
Revision History	3
Table of Contents	4
List of Figures	13
List of Tables	16
1: About this Guide	17
Purpose and Audience	17
Summary of Chapters	17
Additional Documentation	18
2: Introduction	19
Features	19
Models	22
System Features	23
Application Example	24
Hardware Features	25
3: Installation	29
What's in the Box	29
Technical Specifications	30
Physical Installation	31
Typical Installations	35
4: Quick Setup	36
Recommendations	36
IP Address	36
Method #1 Using the Front Panel Display	37
Method #2 Quick Setup on the Web Page	40
Method #3 Quick Setup on the Command Line Interface	42
Next Step	45
5: Web and Command Line Interfaces	46
Web Interface	46
Command Line Interface	48
6: Basic Parameters	52
Requirements	52
IP Filter	58
IP Filter Commands	62
Routing	63
VPN	65
7: Services	68
System Logging and Other Services	68
SSH/Telnet/Logging	68
SNMP	72
NFS and SMB/CIFS	75
Secure Lantronix Network	77
Date and Time	82
Web Server	84
iGoogle Gadgets	88
8: Device Ports	90
Connection Methods	90
Permissions	90
Device Status	91
Global Port Settings	91
Device Ports - Settings	94
Interacting with a Device Port	106
Device Ports - Logging	107
Console Port	112
Power Outlets	114
Host Lists	117
Scripts	121
Sites	134
Modem Dialing States	137
9: USB Port	141
Set Up of USB Storage	141
Manage Firmware and Configuration Files	148
USB Commands	148
10: Connections	150
Typical Setup Scenarios for the SLB	150
11: User Authentication	157
Local and Remote User Settings	160
NIS	168
LDAP	171
RADIUS	176
Kerberos	182
TACACS+	186
Groups	190
SSH Keys	193
Custom Menus	199
12: Maintenance	206
SLB Maintenance	206
Audit Log	219
Email Log	220
Diagnostics	221
Status/Reports	225
Emailing Logs and Reports	227
Events	230
LCD/Keypad	232
Banners	234
13: Application Examples	236
Dial-in (Text Mode) to a Remote Device	238
Local Serial Connection to Network Device via Telnet	239
14: Command Reference	241
Introduction to Commands	241
Administrative Commands	243
Audit Log Commands	251
Authentication Commands	251
Kerberos Commands	252
LDAP Commands	253
Local Users Commands	254
NIS Commands	257
RADIUS Commands	258
TACACS+ Commands	259
User Permissions Commands	260
CLI Commands	262
Connection Commands	264
Custom User Menu Commands	267
Date and Time Commands	269
Device Commands	270
Device Port Commands	271
Diagnostic Commands	274
End Device Commands	276
Events Commands	277
Group Commands	278
Host List Commands	279
IP Filter Commands	280
Logging Commands	281
Network Commands	282
NFS and SMB/CIFS Commands	285
Power Commands	286
Routing Commands	287
Services Commands	288
SLB Network Commands	289
SSH Key Commands	290
Status Commands	292
System Log Commands	294
USB Storage Commands	294
USB Modem Commands	295
Appendix A: Bootloader	297
Accessing the Bootloader	297
Bootload Commands	297
Appendix B: Security Considerations	298
Security Practice	298
Factors Affecting Security	298
Appendix C: Safety Information	299
Safety Precautions	299
Appendix D: Adapters and Pinouts	301
Appendix E: Protocol Glossary	304

Lantronix SLB Lantronix SLB - User Guide - Page 54

Eth1 and Eth2 Settings, Obtain from DHCP

Page 54 highlights