Miele DGC 7585 Operating and Installation instructions - Page 181

Installing and removing the steam oven, Securing the steam oven in the housing unit

Page 181 highlights

*INSTALLATION* Installation Installing and removing the steam oven For safety reasons, the steam oven may only be used when it has been fully installed. Do not open the door when the steam oven is on the floor. This could damage the door. Do not open the door until the steam oven has been installed inside the housing unit. Maintain the required minimum installation height of 36" (914 mm). It is vital to observe the connection data in "Plumbed water connection", "Drainage", and "Electrical connection" under "Installation". The steam generator may malfunction if the steam oven is not on a level surface. The maximum deviation from the horizontal that can be tolerated is 2°.  Push the steam oven into the housing unit and align it in the center of the housing unit. When doing so, make sure that the power cord and water hoses do not get trapped or damaged.  Open the door. 1. 2. Securing the steam oven in the housing unit  Attach the water hoses to the steam oven (see "Attaching the stainlesssteel hose to the steam oven" and "Attaching the plastic hose to the steam oven" under "Installation").  Draw the water hoses through the cutout in the base of the housing unit. Risk of damage from incorrect transportation. Lifting the steam oven by the door handle could cause damage to the door. Use the recessed grips on each side of the housing to carry the appliance.  Insert the mounting aid into the hole in the front frame. 181

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196

Installation
181
Installing and removing the
steam oven
For safety reasons, the steam oven
may only be used when it has been
fully installed.
Do not open the door when the
steam oven is on the floor. This could
damage the door.
Do not open the door until the steam
oven has been installed inside the
housing unit.
Maintain the required minimum in-
stallation height of 36" (914 mm).
It is vital to observe the connection
data in “Plumbed water connection”,
“Drainage”, and “Electrical connec-
tion” under “Installation”.
Securing the steam oven in the hous-
ing unit
Attach the water hoses to the steam
oven (see “Attaching the stainless-
steel hose to the steam oven” and
“Attaching the plastic hose to the
steam oven” under “Installation”).
Draw the water hoses through the
cutout in the base of the housing unit.
Risk of damage from incorrect trans-
portation.
Lifting the steam oven by the door
handle could cause damage to the
door.
Use the recessed grips on each side
of the housing to carry the appliance.
The steam generator may malfunc-
tion if the steam oven is not on a
level surface.
The maximum deviation from the
horizontal that can be tolerated is 2°.
Push the steam oven into the housing
unit and align it in the center of the
housing unit.
When doing so, make sure that the
power cord and water hoses do not
get trapped or damaged.
Open the door.
1.
2.
Insert the mounting aid into the hole
in the front frame.