Miele DGC 7585 Operating and Installation instructions - Page 187

Electrical connection, Connection, Connection data, 240 V/20 A/60 Hz

Page 187 highlights

*INSTALLATION* Installation Electrical connection  Risk of injury due to electric shock. During installation, maintenance, and repair work, the steam oven must be disconnected from the electricity supply: To disconnect the steam oven, fully unscrew the breakers, trip the ground fault circuit interrupter, or unplug the power cord from the socket. To do this, pull the plug, not the power cord.  Risk of injury. Installation, repairs, and other work by unqualified persons could be dangerous. Miele cannot be held liable for unauthorized work. Installation, maintenance, and repairs must only be carried out by a technician authorized by Miele. The connection data (frequency and voltage) on the steam oven's data plate must correspond with those of the electricity supply in order to ensure that no damage can occur to the steam oven. Compare this data before connecting the appliance. If in any doubt, consult a qualified service technician. For safety reasons, the steam oven may only be used after it has been built in.  Important - Save these instructions for the local electrical inspector's use. Connection  Make sure that the connection data on the data plate (voltage, frequency, and fuse rating) matches that of your electricity supply. The data plate is located on the top of the housing. Connection data The steam oven is equipped with a 78 3/4" (2.0 m) power cord with plug for connection to an electricity supply with: 208/240 V/20 A/60 Hz Ensure that the socket is easily accessible after the steam oven has been installed. Temporary or permanent operation on an autonomous power supply system or a power supply system that is not synchronized with the grid power supply (e.g., island networks, back-up systems) is possible. A prerequisite for operation is that the power supply system complies with national and local codes. The function and operation of the protective measures provided in the domestic electrical installation and in this Miele product must also be maintained in isolated operation or in operation that is not synchronized with the grid power supply, or these measures must be replaced by equivalent measures in the installation. 187

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196

Installation
187
Electrical connection
Risk of injury due to electric
shock.
During installation, maintenance, and
repair work, the steam oven must be
disconnected from the electricity
supply:
To disconnect the steam oven, fully
unscrew the breakers, trip the
ground fault circuit interrupter, or un-
plug the power cord from the socket.
To do this, pull the plug, not the
power cord.
Risk of injury.
Installation, repairs, and other work
by unqualified persons could be dan-
gerous. Miele cannot be held liable
for unauthorized work.
Installation, maintenance, and repairs
must only be carried out by a techni-
cian authorized by Miele.
The connection data (frequency and
voltage) on the steam oven’s data
plate must correspond with those of
the electricity supply in order to en-
sure that no damage can occur to
the steam oven.
Compare this data before connecting
the appliance. If in any doubt, con-
sult a qualified service technician.
For safety reasons, the steam oven
may only be used after it has been
built in.
Important  – Save these instructions
for the local electrical inspector’s use.
Connection
Make sure that the connection data
on the data plate (voltage, frequency,
and fuse rating) matches that of your
electricity supply.
The data plate is located on the top of
the housing.
Connection data
The steam oven is equipped with a
78 3/4” (2.0 m) power cord with plug for
connection to an electricity supply with:
208/240 V/20 A/60 Hz
Ensure that the socket is easily accessi-
ble after the steam oven has been in-
stalled.
Temporary or permanent operation on
an autonomous power supply system or
a power supply system that is not
synchronized with the grid power
supply (e.g., island networks, back-up
systems) is possible. A prerequisite for
operation is that the power supply sys-
tem complies with national and local
codes.
The function and operation of the
protective measures provided in the
domestic electrical installation and in
this Miele product must also be main-
tained in isolated operation or in opera-
tion that is not synchronized with the
grid power supply, or these measures
must be replaced by equivalent mea-
sures in the installation.