Uniden BCD325P2 Owners Manual - Page 54

Set Modulation, Set Attenuator, Set Lockout

Get Uniden BCD325P2 PDF manuals and user guides View all Uniden BCD325P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Set Modulation This setting selects the modulation used for the site. The default setting is auto (NFM for FM frequencies). See also Band Defaults. 1. Scroll to 'Set Modulation' and press E/yes. 2. Scroll to Auto, NFM, or FM and press E/yes. Note: You can also toggle modulation for a site in hold mode by pressing Func then 9(mod). Set Attenuator This setting controls whether the scanner attenuates signals on this site by about 20 dB. The default setting is off. 1. Scroll to 'Set Attenuator' and press E/yes. 2. Scroll to On or Off and press E/yes to save and exit. Note: You can also toggle attenuation for a site in hold mode by pressing Func then 7(att). Set Lockout Determines whether a site will be scanned or not (even if the quick key for the site is turned on). 'Temporary L/O' locks out the site until you cycle power. The default setting is unlocked. 1. Scroll to 'Set Lockout' and press E/yes. 2. Scroll to 'Unlocked', 'Temporary L/O', or 'Lockout' and press E/yes to save and exit. Note: You can also toggle lockout by holding the site and quickly pressing Func then L/O. Set Hold Time Sets (in seconds) the amount of time the scanner will scan the system before moving on to the next system. All (unlocked) channels will be scanned at least once regardless of this setting. The scanner moves to the next system after the hold time expires, any current transmission ends, and the channel delay time expires. The default setting is 0 seconds for each system. 1. Scroll to 'Set Hold Time' and press E/yes. 2. Enter the hold time (0-255 seconds) you desire and press E/yes to save and exit. 54

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
54
Set Modulation
This setting selects the modulation used for the site. The default setting is auto (NFM
for FM frequencies). See also Band Defaults.
1.
Scroll to ‘Set Modulation’ and press
E/yes
.
2.
Scroll to Auto, NFM, or FM and press
E/yes
.
Note: You can also toggle modulation for a site in hold mode by pressing
Func
then
9(mod)
.
Set Attenuator
This setting controls whether the scanner attenuates signals on this site by about 20
dB. The default setting is off.
1.
Scroll to ‘Set Attenuator’ and press
E/yes
.
2.
Scroll to On or Off and press
E/yes
to save and exit.
Note: You can also toggle attenuation for a site in hold mode by pressing
Func
then
7(att)
.
Set Lockout
Determines whether a site will be scanned or not (even if the quick key for the site
is turned on). ‘Temporary L/O’ locks out the site until you cycle power. The default
setting is unlocked.
1.
Scroll to ‘Set Lockout’ and press
E/yes
.
2.
Scroll to ‘Unlocked’, ‘Temporary L/O’, or ‘Lockout’ and press
E/yes
to save
and exit.
Note: You can also toggle lockout by holding the site and quickly pressing
Func
then
L/O
.
Set Hold Time
Sets (in seconds) the amount of time the scanner will scan the system before
moving on to the next system. All (unlocked) channels will be scanned at least once
regardless of this setting. The scanner moves to the next system after the hold time
expires, any current transmission ends, and the channel delay time expires. The
default setting is 0 seconds for each system.
1.
Scroll to ‘Set Hold Time’ and press
E/yes
.
2.
Enter the hold time (0-255 seconds) you desire and press
E/yes
to save and
exit.