Uniden BCD325P2 Owners Manual - Page 74

Gps Review Location Mode

Get Uniden BCD325P2 PDF manuals and user guides View all Uniden BCD325P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

To Toggle 'Hold' mode on a background Scan/Srch press Hold. To Return to Scan mode press Scan/Srch. Press GPS again to view GPS Display Mode. To View 'Review Location' Mode press E/yes. Notes: All sites/groups (with quick keys enabled and gps enabled for the site/ group) not within range of your current location will be temporarily locked out. If you try to use a quick key to enable a site/group for scan that is out of range of your current location, you will see 'Location L/O' and then site/group name (only once), and it will temporary lock out the site/group. If you disconnect/turn off your GPS unit, you will see 'No GPS Input' in GPS display mode and the scanner will return to scanning any sites/groups that the scanner did not temporary lock out. To restore all sites/groups, cycle the scanner off then on. If you lose the satellite signal, you will see 'Searching for Satellite' until the GPS unit reacquires a signal. If a GPS is detected as soon as the scanner is turned on, the scanner displays "GPS CONNECTED" instead of displaying individual lock/unlock messages for groups/sites. It applies the location-based rules to all systems at one time. GPS REVIEW LOCATION MODE If you have programmed data for a Point of Interest, Dangerous Crossing, and a Dangerous Road, you can review the type, range setting, and location information for each location. Hold on any channel and press Func then E/yes(gps) to enter GPS display mode then press E/yes. The most recently stored location is displayed. Use the scroll control to display the next screen for review. Note: the scanner will mute in this mode. Important: while you are in Review Location Mode and press and hold GPS for 2 seconds, the data of the new point will overwrite the currently displayed data. 74

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
74
To Toggle ‘Hold’ mode on a background
Scan/Srch
press
Hold
.
To Return to Scan mode press
Scan/Srch
.
Press
GPS
again to view GPS Display Mode.
To View ‘Review Location’ Mode press
E/yes
.
Notes:
All sites/groups (with quick keys enabled and gps enabled for the site/
group) not within range of your current location will be temporarily locked out.
If you try to use a quick key to enable a site/group for scan that is out of range
of your current location, you will see ‘Location L/O’ and then site/group name
(only once), and it will temporary lock out the site/group.
If you disconnect/turn off your GPS unit, you will see ‘No GPS Input’ in GPS
display mode and the scanner will return to scanning any sites/groups that
the scanner did not temporary lock out. To restore all sites/groups, cycle the
scanner off then on.
If you lose the satellite signal, you will see ‘Searching for Satellite’ until the
GPS unit reacquires a signal.
If a GPS is detected as soon as the scanner is turned on, the scanner displays
“GPS CONNECTED” instead of displaying individual lock/unlock messages for
groups/sites. It applies the location-based rules to all systems at one time.
GPS REVIEW LOCATION MODE
If you have programmed data for a Point of Interest, Dangerous Crossing, and a
Dangerous Road, you can review the type, range setting, and location information
for each location.
Hold on any channel and press Func then E/yes(gps) to enter GPS display mode
then press E/yes. The most recently stored location is displayed. Use the scroll
control to display the next screen for review.
Note: the scanner will mute in this mode.
Important:
while you are in Review Location Mode and press and hold GPS for 2
seconds, the data of the new point will overwrite the currently displayed data.