Uniden BCD325P2 Owners Manual - Page 92

E/yes, CTCSS/DCS Search, P25 NAC Search, Repeater Find, Max Auto Store, Set Delay Time, Set

Get Uniden BCD325P2 PDF manuals and user guides View all Uniden BCD325P2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 92 highlights

1. Scroll to 'Tone/Code Search' and press E/yes. 2. Scroll to 1 of 3 options and press E/yes. Off - the scanner does not search and display any tones. CTCSS/DCS Search - the scanner searches and displays only CTCSS/ DCS tones. P25 NAC Search - the scanner searches and displays only NAC tones. Repeater Find this feature sets whether the scanner tries to tune to a repeater output frequency when it detects a transmission on a repeater input frequency in Search and Close Call modes. Since you can normally only hear one side of a conversation when you listen to an input frequency transmission, turning this feature on can let you hear both sides of the conversation on the output frequency. If the scanner detects the transmission on the output frequency, it beeps and 'Repeater Found' appears, and it remains on the output frequency until transmissions end. The default setting is Off. 1. Scroll to 'Repeater Find' and press E/yes. 2. Scroll to On or Off and press E/yes to save and exit. Max Auto Store this value sets how many hits the scanner will automatically store when it is in either Search and Store or Close Call Auto Store mode. When the scanner reaches the maximum number of hits you set, it stops the auto-store operation. 1. Scroll to 'Max Auto Store' and press E/yes. 2. Enter a value from 1-256 then press E/yes to save and exit. Set Delay Time this setting determines how long the scanner waits after a transmission ends before resuming Quick Search and Close Call Search operations. A negative delay will force a resume after that number of seconds. The default setting is 2 seconds. 1. Scroll to 'Set Delay Time' and press E/yes. 2. Scroll to the desired delay time (-10, -5, -2, 0, 1, 2, 5, 10, or 30 secs.) and press E/yes to save and exit. Set Attenuator this setting controls the attenuator for Quick Search, Close Call, and Band Scope operations. Turn on this setting if you are near other strong signal sources to attenuate about 20dB. Attenuation sometimes helps to reduce interference and desensitization that strong signals create. The default setting is Off. 1. Scroll to 'Set Attenuator' and press E/yes. 2. Scroll to On or Off and press E/yes to save and exit. Note: You can also toggle attenuation for search/close call mode by pressing Func then 7(att). 92

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
92
1.
Scroll to ‘Tone/Code Search’ and press
E/yes
.
2.
Scroll to 1 of 3 options and press
E/yes
.
Off
- the scanner does not search and display any tones.
CTCSS/DCS Search
- the scanner searches and displays only CTCSS/
DCS tones.
P25 NAC Search
- the scanner searches and displays only NAC tones.
Repeater Find
this feature sets whether the scanner tries to tune to a repeater
output frequency when it detects a transmission on a repeater input frequency in
Search and Close Call modes. Since you can normally only hear one side of a
conversation when you listen to an input frequency transmission, turning this feature
on can let you hear both sides of the conversation on the
output
frequency. If the
scanner detects the transmission on the output frequency, it beeps and ‘Repeater
Found’ appears, and it remains on the output frequency until transmissions end.
The
default setting is Off.
1.
Scroll to ‘Repeater Find’ and press
E/yes
.
2.
Scroll to On or Off and press
E/yes
to save and exit.
Max Auto Store
this value sets how many hits the scanner will automatically
store when it is in either Search and Store or Close Call Auto Store mode. When
the scanner reaches the maximum number of hits you set, it stops the auto-store
operation.
1.
Scroll to ‘Max Auto Store’ and press
E/yes
.
2.
Enter a value from
1-256
then press
E/yes
to save and exit.
Set Delay Time
this setting determines how long the scanner waits after a
transmission ends before resuming Quick Search and Close Call Search operations.
A negative delay will force a resume after that number of seconds. The default
setting is 2 seconds.
1.
Scroll to ‘Set Delay Time’ and press
E/yes
.
2.
Scroll to the desired delay time (-10, -5, -2, 0, 1, 2, 5, 10, or 30 secs.) and
press
E/yes
to save and exit.
Set Attenuator
this setting controls the attenuator for Quick Search, Close Call,
and Band Scope operations. Turn on this setting if you are near other strong
signal sources to attenuate about 20dB. Attenuation sometimes helps to reduce
interference and desensitization that strong signals create. The default setting is Off.
1.
Scroll to ‘Set Attenuator’ and press
E/yes
.
2.
Scroll to On or Off and press
E/yes
to save and exit.
Note: You can also toggle attenuation for search/close call mode by pressing
Func
then
7(att)
.