Brother International HS-5300 Service Manual - Page 96

reassembling.

Get Brother International HS-5300 PDF manuals and user guides View all Brother International HS-5300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 96 highlights

PR98064 (8) Remove two screws (A) and two screws (B) and remove the Head from the Carriage ASSY. C) (B) Carriage ASSY CR PCB ASSY (A) Heat insulation film Head ASSY Fig. 4.69 (1) Put the Gap spacer on the Carriage ASSY. As shown in fig. 4.70, place the Head ASSY on the Carriage ASSY to keep the 0.18 mm gap between the Head ASSY and the reference surface. (2) Tighten the screws (A) first, then (B) while pushing down the Head ASSY using a screw driver. Refer to fig. 4.69 for the screws. Remove the Gap spacer. (Di Screw driver Carriage ASSY Head ASSY Reference surfaces of the window O r Reference surfaces of the window Window of the carriage 0.18mm 0.18mm Carriage Fig. 4.70 Note: Make sure that there is 0.18 mm gap between the Carriage ASSY and the Head ASSY. Be sure to remove the Gap spacer after reassembling. III-44

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
PR98064
(8)
Remove
two
screws
(A)
and
two
screws
(B)
and
remove
the
Head
from
the
Carriage
ASSY.
C)
(B)
Carriage
ASSY
CR
PCB
ASSY
Heat
insulation
film
Head
ASSY
Fig.
4.69
<Reassembly>
(A)
(1)
Put
the
Gap
spacer
on
the
Carriage
ASSY.
As
shown
in
fig.
4.70,
place
the
Head
ASSY
on
the
Carriage
ASSY
to
keep
the
0.18
mm
gap
between
the
Head
ASSY
and
the
reference
surface.
(2)
Tighten
the
screws
(A)
first,
then
(B)
while
pushing
down
the
Head
ASSY
using
a
screw
driver.
Refer
to
fig.
4.69
for
the
screws.
Remove
the
Gap
spacer.
Reference
surfaces
of
the
window
0.18mm
Window
of
the
carriage
(Di
r
O
Fig.
4.70
Carriage
ASSY
Carriage
Screw
driver
Head
ASSY
Reference
surfaces
of
the
window
0.18mm
Note:
Make
sure
that
there
is
0.18
mm
gap
between
the
Carriage
ASSY
and
the
Head
ASSY.
Be
sure
to
remove
the
Gap
spacer
after
reassembling.
III
-44